10338Extreme Networks 10338 Compatible 10G SFP+ T Transceiver Module
Built for hosts recognizing 10338, this HT-manufactured SFP+ module delivers 10G transmission at the listed wavelength plan. Its rated reach is 30m on Cat6a / Cat7 or Better, with RJ-45 as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 10338HT Part Number: SFP-10G-T-30
Product Highlights
- Compatible alternative to Extreme Networks 10338
- 10G connectivity at 10Gbps
- Specified reach: 30m on Cat6a / Cat7 or Better
- RJ-45 / Copper interface
- Digital diagnostic monitoring: Not Implemented
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| Extreme Networks Compatible | 10338 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10G-T-30 |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Max. Power Consumption | ≤2.5W |
| Max. Transmission Distance | 30m@Cat6a/Cat7 or Better |
| Connector | RJ-45 |
| Cable Type | Copper |
| Special Features | RX_LOS |
| DDM/DOM | Not Implemented |
| Multi-rate Application | Not Supported |
| EMC (Electro Magnetic Compatibility) | Supported |
| MTBF | 5,000,000 Hours |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3an, IEEE 802.3az, SFP+ MSA, SFF-8431 |
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this copper interface, use the stated cable category and keep the channel within 30m on Cat6a / Cat7 or Better. Patch-cord construction, connector quality and auto-negotiation can affect the result. Verify the negotiated speed and diagnostics at both ends rather than assuming every RJ-45 port behaves identically.
Extreme Networks Compatibility and Factory Testing
Factory verification starts with the expected 10338 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Not Implemented. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10Gbps, rated reach 30m on Cat6a / Cat7 or Better.
Ordering Information
Use 10338 as the compatibility cross-reference and SFP-10G-T-30 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each 10338 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Extreme Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 10338, not an original Extreme Networks-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Copper. The rated reach is 30m on Cat6a / Cat7 or Better, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
