MTP-12 to MTP-12 UPC Jumper, 12 FibersMTP-12 to MTP-12 UPC Jumper, 12 Fibers, OM3, Type B
A ready to install MTP® Elite Female jumper: 12 Fibers, OM3 50/125μm, Plenum (OFNP). Pre-termination means no polishing, no epoxy and no curing time on site - just route the cable, plug in both ends and bring the link up.
Available lengths are 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft) and 10m (33ft). We can also produce any intermediate or longer length to order, with your choice of labeling and packaging.
Product Highlights
- MTP® Elite Female (Non-Pinned) to MTP® Elite Female (Non-Pinned), 12 Fibers
- OM3 50/125μm, bend insensitive fiber
- Insertion loss ≤0.35dB (0.15dB Typ.), return loss ≥27dB
- Type B polarity
- 3.0mm Plenum (OFNP) round cable
- Minimum bend radius 7.5mm
- Stock lengths from 1m (3ft) to 10m (33ft), custom lengths on request
Specifications
| Part Number | 12FMTPOM3 |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP® Elite Female (Non-Pinned) |
| Connector B | US Conec MTP® Elite Female (Non-Pinned) |
| Fiber Mode | OM3 50/125μm |
| Wavelength | 850/1300nm |
| Polish Type | UPC to UPC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 12 Fibers |
| Glass Fiber | Bend Insensitive Fiber |
| Cable Outside Diameter (OD) | 3.0mm |
| Min. Bend Radius (Optical Fiber) | 7.5mm |
| Min. Bend Radius (Fiber Cable) | 20/10D (Dynamic/Static) |
| Connector Durability | 500 times |
| Tensile Strength | 90/180N (Long/Short Term) |
| Insertion Loss | ≤0.35dB (0.15dB Typ.) |
| Return Loss | ≥27dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
Use this jumper anywhere a short multi-fiber connection is needed: panel to equipment, cassette to cassette, or switch to switch within a row. A 12-fiber MPO interface carries 8 active lanes for 40G SR4 and 100G SR4 links, leaving the remaining 4 fibers dark, exactly as the MSA wiring specifies. Because it arrives polished and tested, the installer only needs to route and connect it.
Polarity and Gender Options
The same jumper can be produced with different polarity and gender combinations. Male connectors carry guide pins for direct module connection, while female versions are used at panels. Polarity A, B and C are all standard for us, and our engineers can check your link diagram if you are unsure which one to order.
Ordering Information
Please reference 12FMTPOM3 in your enquiry. Our sales team can also advise on polarity, gender and jacket choices if your project documentation is not final yet.
Built to Your Spec
Our engineering team handles custom MPO/MTP assemblies daily. If the standard configuration does not match your link design, send us the requirement and we will build exactly what your network needs at factory-direct cost.
How We Pack
Products are packed in anti-static or PE bags with connector dust caps fitted, then boxed in sturdy export cartons. Custom labels, barcodes and carton markings are available on request.
Quality and Testing
Every MPO/MTP assembly leaving our factory is 100% tested for insertion loss and return loss, with end face geometry checks on the multi-fiber ferrules. Controlled polishing keeps the loss budget stable across the whole batch, which matters when several mated pairs sit in one link.
