MTP-16 to 2 x MTP-8 APC Breakout CableMTP-16 to 2 x MTP-8 APC Breakout Cable, 16 Fibers, OS2, Crossover
A MTP®-16 Female APC with Offset Key breakout cable for parallel to parallel or parallel to duplex connections. 16 Fibers, OS2 9/125μm, Plenum (OFNP). Each leg is labeled and length matched in the factory for a clean installation.
Standard lengths are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 40m (131ft). Because we are the manufacturer, any other length between or beyond these steps can be produced on request, with your choice of jacket color, labeling and packaging.
Product Highlights
- MTP®-16 Female (Non-Pinned) APC with Offset Key to MTP®-8 Female (Non-Pinned) APC, 16 Fibers
- OS2 9/125μm, G.657.A1
- Insertion loss ≤0.35dB (0.15dB Typ.), return loss ≥65dB
- Crossover polarity
- 3.0mm Plenum (OFNP) round cable
- Minimum bend radius 10mm
- Ten standard lengths from 1m (3ft) to 40m (131ft), custom lengths built to order
Specifications
| Part Number | 16FMTPSMF |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP®-16 Female (Non-Pinned) APC with Offset Key |
| Connector B | US Conec MTP®-8 Female (Non-Pinned) APC |
| Fiber Mode | OS2 9/125μm |
| Wavelength | 1310/1550nm |
| Polish Type | APC to APC |
| Polarity | Crossover |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 16 Fibers |
| Glass Fiber | G.657.A1 |
| Minimum Bend Radius | 10mm |
| Cable Outside Diameter (OD) | 3.0mm |
| Breakout Length | 0.5m |
| Installation Tensile Load | 66N |
| Tensile Strength | 60/120N (Long/Short Term) |
| Insertion Loss | ≤0.35dB (0.15dB Typ.) |
| Return Loss | ≥65dB |
| Attenuation at 1310nm | ≤0.35dB/km |
| Attenuation at 1550nm | ≤0.21dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
This breakout is used wherever one multi-fiber interface must serve several devices. The 16-fiber interface matches 400G SR8 optics, where all 16 fibers carry active transmit and receive lanes. The factory controlled fan-out keeps each leg at the right length and polarity, avoiding the tangle of separate patch cords.
Breakout Geometry and Wiring
Each breakout leg is individually jacketed, labeled and measured, and the transition from trunk to legs is protected against pulling forces. If your installation needs different leg lengths or a different lane mapping, we can build it to your drawing.
Ordering Information
Please reference 16FMTPSMF in your enquiry. The 1m (3ft) version is the standard model; Our sales team can also advise on polarity, gender and jacket choices if your project documentation is not final yet.
Quality and Testing
Our test routine covers insertion loss, return loss and ferrule end face inspection on every assembly. Because testing is done in-house, custom variants receive exactly the same verification as standard models.
Built to Your Spec
As a factory we can modify almost every detail of this product: length, jacket material and color, polarity, gender, breakout geometry, labeling and packaging. Non-standard variants are routine work for us, not a special project.
Logistics
Standard configurations normally ship within a few working days by DHL, UPS, FedEx, TNT or EMS. For project quantities we arrange air or sea freight, and we can ship on your own courier account or deliver to your appointed forwarder.
