1G-SFP-ZRD-1563.86Brocade 1G-SFP-ZRD-1563.86 Compatible 1G SFP Transceiver Module 40km
Built for hosts recognizing 1G-SFP-ZRD-1563.86, this HT-manufactured SFP module delivers 1G transmission at 1563.86nm. Its rated reach is 40km, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 1G-SFP-ZRD-1563.86HT Part Number: DW-SFP1G40-17
Product Highlights
- Compatible alternative to Brocade 1G-SFP-ZRD-1563.86
- 1G connectivity at 1000Mbps
- Optical wavelength: 1563.86nm
- Specified reach: 40km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Brocade Compatible | 1G-SFP-ZRD-1563.86 |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP1G40-17 |
| Form Factor | SFP |
| Max Data Rate | 1000Mbps |
| Wavelength | 1563.86nm |
| Max Cable Distance | 40km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DML |
| Receiver Type | PIN |
| Receiver Sensitivity | < -24dBm |
| SMSR | 30dB |
| TX Power | 0~5dBm |
| RX Power | -24~-1dBm |
| Power Consumption | 2W |
| Power Budget | 24dB |
| EMC (Electro Magnetic Compatibility) | Supported |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | SFP MSA, SFF-8472 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1563.86nm, then include their insertion loss in the 40km power budget. A nearby channel is not a substitute for the specified wavelength.
Brocade Compatibility and Factory Testing
Compatibility testing for 1G-SFP-ZRD-1563.86 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is < -24dBm; the stated optical power budget is 24dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 1000Mbps, wavelength 1563.86nm, rated reach 40km.
Ordering Information
Use 1G-SFP-ZRD-1563.86 as the compatibility cross-reference and DW-SFP1G40-17 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each 1G-SFP-ZRD-1563.86 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 1G-SFP-ZRD-1563.86, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
