MTP-24 to 3 x MTP-8 APC Breakout CableMTP-24 to 3 x MTP-8 APC Breakout Cable, 24 Fibers, OS2, Type B
This MTP® Elite Female breakout cable splits a high density multi-fiber interface into smaller legs, so one port can feed several lower speed links. OS2 9/125μm fiber and Plenum (OFNP) jacket with 24 Fibers make it a tidy alternative to cassette based fan-out.
Standard lengths are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 40m (131ft). Because we are the manufacturer, any other length between or beyond these steps can be produced on request, with your choice of jacket color, labeling and packaging.
Product Highlights
- MTP® Elite Female (Non-Pinned) to MTP® Elite Female (Non-Pinned), 24 Fibers
- OS2 9/125μm, G.657.A1
- Insertion loss ≤0.35dB (0.15dB Typ.), return loss ≥60dB
- Type B polarity
- 3.0mm Plenum (OFNP) round cable
- Minimum bend radius 10mm
- Ten standard lengths from 1m (3ft) to 40m (131ft), custom lengths built to order
Specifications
| Part Number | 24FMTPSMF |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP® Elite Female (Non-Pinned) |
| Connector B | US Conec MTP® Elite Female (Non-Pinned) |
| Fiber Mode | OS2 9/125μm |
| Wavelength | 1310/1550nm |
| Polish Type | APC to APC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 24 Fibers |
| Glass Fiber | G.657.A1 |
| Minimum Bend Radius | 10mm |
| Cable Outside Diameter (OD) | 3.0mm |
| Breakout Length | 0.5m |
| Installation Tensile Load | 66N |
| Tensile Strength | 80/240N (Long/Short Term) |
| Insertion Loss | ≤0.35dB (0.15dB Typ.) |
| Return Loss | ≥60dB |
| Attenuation at 1310nm | ≤0.35dB/km |
| Attenuation at 1550nm | ≤0.21dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
In leaf-spine and GPU cluster cabling, this breakout replaces a cassette plus multiple jumpers with one tested assembly. A 24-fiber MPO interface is the standard for 100GBASE-SR10 CFP, CFP2 and CPAK modules, and is equally at home in structured trunking between panels. Each leg is marked so port mapping is unambiguous during installation.
Breakout Geometry and Wiring
The fan-out point is factory molded and strain relieved, with each breakout leg built to the length shown in the specification table. Wiring follows the polarity scheme listed, so the lane order at the far end matches the transceiver requirements without on-site re-termination.
Ordering Information
Please reference 24FMTPSMF in your enquiry. The 1m (3ft) version is the standard model; Our sales team can also advise on polarity, gender and jacket choices if your project documentation is not final yet.
How We Pack
Every cable is protected with dust caps and individual packaging before being boxed for shipment. Batch test reports and your own part number labels can be included in each bag.
Quality and Testing
Our test routine covers insertion loss, return loss and ferrule end face inspection on every assembly. Because testing is done in-house, custom variants receive exactly the same verification as standard models.
Built to Your Spec
We have manufactured fiber optic assemblies since 1995. MPO and MTP cabling is one of our core lines: fiber counts from 8 to 144, single mode and multimode, UPC and APC polish, trunk, jumper, harness and breakout formats. Send your drawing and we turn it into a ready to install assembly.
