MTP-12 to 2 x MTP-4 APC Breakout Cable, 8MTP-12 to 2 x MTP-4 APC Breakout Cable, 8 Fibers, OM4, Type B
Factory built MTP® Elite Female breakout assembly with 8 Fibers on OM4 50/125μm fiber. The main trunk stays one cable until the fan-out point, which keeps pathways clear and makes moves and changes much easier to trace.
Standard lengths are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 40m (131ft). Because we are the manufacturer, any other length between or beyond these steps can be produced on request, with your choice of jacket color, labeling and packaging.
Product Highlights
- MTP® Elite Female (Non-Pinned) to MTP® Elite Female (Non-Pinned), 8 Fibers
- OM4 50/125μm, bend insensitive fiber
- Insertion loss ≤0.35dB (0.15dB Typ.), return loss ≥45dB
- Type B polarity
- 3.0mm Plenum (OFNP) round cable
- Minimum bend radius 7.5mm
- Ten standard lengths from 1m (3ft) to 40m (131ft), custom lengths built to order
Specifications
| Part Number | 8FMTPOM4 |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP® Elite Female (Non-Pinned) |
| Connector B | US Conec MTP® Elite Female (Non-Pinned) |
| Fiber Mode | OM4 50/125μm |
| Wavelength | 850/1300nm |
| Polish Type | APC to APC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 8 Fibers |
| Glass Fiber | Bend Insensitive Fiber |
| Minimum Bend Radius | 7.5mm |
| Cable Outside Diameter (OD) | 3.0mm |
| Trunk Length | 0.2m |
| Installation Tensile Load | 66N |
| Tensile Strength | 60/120N (Long/Short Term) |
| 400G Ethernet Distance | 50/100m at 850nm |
| 800G Ethernet Distance | 50m at 850nm |
| Insertion Loss | ≤0.35dB (0.15dB Typ.) |
| Return Loss | ≥45dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
This breakout is used wherever one multi-fiber interface must serve several devices. The 8-fiber version matches 400G and 800G parallel interfaces that run on 4 or 8 lanes, such as QSFP112, OSFP and twin-port OSFP connections. The factory controlled fan-out keeps each leg at the right length and polarity, avoiding the tangle of separate patch cords.
Breakout Geometry and Wiring
The fan-out point is factory molded and strain relieved, with each breakout leg built to the length shown in the specification table. Wiring follows the polarity scheme listed, so the lane order at the far end matches the transceiver requirements without on-site re-termination.
Ordering Information
Ordering is simple: send us 8FMTPOM4 and your required lengths and quantities, and we return a factory quote the same working day. The 1m (3ft) version is the standard model; Small trial orders are welcome before you commit to a full project rollout.
Logistics
We dispatch worldwide by international courier, with air and sea freight options for bulk orders. Goods can be sent collect on your courier account, and documentation for customs clearance is provided with every shipment.
Quality and Testing
Our test routine covers insertion loss, return loss and ferrule end face inspection on every assembly. Because testing is done in-house, custom variants receive exactly the same verification as standard models.
Built to Your Spec
We have manufactured fiber optic assemblies since 1995. MPO and MTP cabling is one of our core lines: fiber counts from 8 to 144, single mode and multimode, UPC and APC polish, trunk, jumper, harness and breakout formats. Send your drawing and we turn it into a ready to install assembly.
