AFBR-89CEHZBrocade AFBR-89CEHZ Compatible 100G QSFP28 SR4 Transceiver Module
The AFBR-89CEHZ compatible module serves equipment requiring a 100G QSFP28 interface with 850nm optics and a 100m rating. Connection is through MPO-12. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: AFBR-89CEHZHT Part Number: QSFP-SR4-100GM
Product Highlights
- Compatible alternative to Brocade AFBR-89CEHZ
- 100G connectivity at Dual Rate 103.1Gbps and 112Gbps
- Optical wavelength: 850nm
- Specified reach: 100m
- MPO-12 / MMF interface
- Operating temperature: 0 to 70°C
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Brocade Compatible | AFBR-89CEHZ |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-SR4-100GM |
| Form Factor | QSFP28 |
| Max Data Rate | Dual Rate 103.1Gbps and 112Gbps |
| Wavelength | 850nm |
| Max Cable Distance | 100m |
| Connector | MPO-12 |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | VCSEL |
| TX Power | -8.4~2.4 dBm |
| Receiver Sensitivity | ＜-10.3 dBm |
| Power Budget | 1.9dB |
| Receiver Overload | 2.4 dBm |
| Power Consumption | ＜2.5W |
| Extinction Ratio | ＞2 dB |
| DOM | Supported |
| Commercial Temperature Range | 0 to 70°C |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Protocols | IEEE Std 802.3-2018, FC-PI-6P, SFF-8665, SFF-8636, SFF-8679 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12 interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 100m figure applies only under suitable cabling conditions. Inspect every MPO-12 mating point and match the remote optical standard.
Brocade Compatibility and Factory Testing
Compatibility testing for AFBR-89CEHZ combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.4~2.4 dBm; receiver sensitivity is ＜-10.3 dBm; the stated optical power budget is 1.9dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate Dual Rate 103.1Gbps and 112Gbps, wavelength 850nm, rated reach 100m.
Ordering Information
When ordering, specify AFBR-89CEHZ, QSFP-SR4-100GM, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies AFBR-89CEHZ, not an original Brocade-branded module.
Which fiber and connector are required?
Use MPO-12 with MMF. The specified maximum reach is 100m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
