10/100BASE-T SFPGeneric Cable Series Compatible 50G SFP56 Active Copper Twinax Cable
The Cable Series compatible series is designed for Generic hosts requiring a 50G ACC connection. Its SFP56 arrangement is supplied as an active copper assembly with the cable and signal-conditioning interfaces supplied together. Use the specifications to assess the physical assembly, then follow the exact length and part-number links when preparing a bill of materials or requesting a compatibility check.
Series Part Number: Cable SeriesHT Part Number: Cable Series
Product Highlights
- HT-manufactured compatible alternative for Generic Cable Series
- 50G aggregate connectivity at 50Gbps
- Interface configuration: SFP56
- Active Twinax
- Length configurations covered: 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft) and 7m (23ft)
- Conductor specification: 30AWG
- Power consumption: ≤0.5W
- Operating temperature: 0 to 70°C (32 to 158°F)
Available Lengths and Corresponding Part Numbers
The documented configurations are 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft) and 7m (23ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.
Compatible OEM Part Numbers
- Cable Series-1M3FT
- SFP56-50G-ACC-2M7FT
- SFP56-50G-ACC-3M10FT
- SFP56-50G-ACC-5M16FT
- SFP56-50G-ACC-7M23FT
- Cable Series
Specifications
| Compatible | Generic |
|---|---|
| Manufacturer | HT |
| HT Part Number | Cable Series |
| Form Factor | SFP56 |
| Max Data Rate | 50Gbps |
| Cable Type | Active Twinax |
| Max Cable Distance | Up to 7m |
| Cable Length Options Covered | 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft) and 7m (23ft) |
| Wire AWG | 30AWG |
| Power Consumption | ≤0.5W |
| Jacket Material | PVC |
| Storage Temperature | -40 to 85°C (-40 to 185°F) |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Modulation Technology | PAM4 |
| Bit Rate | 53.125 Gbps |
| Protocol | SFP56 MSA |
Applications and Deployment
Active copper assemblies add signal conditioning while retaining the convenience of a direct-attached cable. They are appropriate where the equipment supports the stated active-cable type and the route exceeds the practical limits of a comparable passive assembly. Per-end power, airflow and host qualification should be assessed before high-density deployment. For this series, the listed interface is SFP56 and the aggregate rate is 50G.
Generic Compatibility and Factory Testing
Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Cable Construction and Routing
The specification table records the conductor specification is 30AWG; the jacket material is PVC; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is ≤0.5W. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.
Structured Pathways and Serviceability
Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this series, keep the interface rate, ACC construction and length-specific OEM reference together throughout that review.
Ordering Information
Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number Cable Series identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Frequently Asked Questions
Is this an original Generic cable?
No. It is an HT-manufactured compatible cable for equipment that specifies Cable Series, not an original Generic-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
Does this ACC cable require separate modules at each end?
No. The connector ends and cable form one complete direct-attach assembly. The ends are not detachable standalone transceivers, and the complete product is tested together.
What information helps confirm compatibility?
Provide the equipment manufacturer and model, port type, hardware revision and software release, together with the required OEM reference, length and quantity. Breakout projects should also identify the intended lane configuration.
