10/100BASE-T SFPDell CFP-100GBASE-SR10 Compatible 100G CFP SR10 Transceiver Module
Built for hosts recognizing CFP-100GBASE-SR10, this HT-manufactured CFP module delivers 100G transmission at 850nm. Its rated reach is 150m on OM4, 100m on OM3, with its specified interface as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CFP-100GBASE-SR10HT Part Number: CFP-SR10-100G
Product Highlights
- Compatible alternative to Dell CFP-100GBASE-SR10
- 100G connectivity at 103.1 Gbp
- Optical wavelength: 850nm
- Specified reach: 150m on OM4, 100m on OM3
- MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Dell Compatible | CFP-100GBASE-SR10 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CFP-SR10-100G |
| Form Factor | CFP |
| Max Data Rate | 103.1 Gbp |
| Wavelength | 850nm |
| Max Cable Distance | 150m@OM4, 100m@OM3 |
| Interface | MTP/MPO-24 |
| Optical Components | 10x VCSEL |
| Media | MMF |
| DOM Support | Yes |
| Modulation (Electrical) | 10x 10G-NRZ |
| Modulation (Optical) | 10x 10G-NRZ |
| Protocols | MSA Compliant |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CFP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 150m on OM4, 100m on OM3 reach. Keep the end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Dell Compatibility and Factory Testing
Factory verification starts with the expected CFP-100GBASE-SR10 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 103.1 Gbp, wavelength 850nm, rated reach 150m on OM4, 100m on OM3.
Ordering Information
When ordering, specify CFP-100GBASE-SR10, CFP-SR10-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each CFP-100GBASE-SR10 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Dell transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CFP-100GBASE-SR10, not an original Dell-branded module.
Which fiber and connector are required?
Use the specified optical connector with MMF. The specified maximum reach is 150m on OM4, 100m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
