CFP-ER4-40KMCiena CFP-ER4-40KM Compatible 100G CFP ER4 Transceiver Module
Built for hosts recognizing CFP-ER4-40KM, this HT-manufactured CFP module delivers 100G transmission at 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm. Its rated reach is 40km, with its specified interface as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CFP-ER4-40KMHT Part Number: CFP-ER4-100G
Product Highlights
- Compatible alternative to Ciena CFP-ER4-40KM
- 100G connectivity at 103.1 Gbp
- Optical wavelength: 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm
- Specified reach: 40km
- SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Ciena Compatible | CFP-ER4-40KM |
|---|---|
| Manufacturer | HT |
| HT Part Number | CFP-ER4-100G |
| Form Factor | CFP |
| Max Data Rate | 103.1 Gbp |
| Wavelength | 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm |
| Max Cable Distance | 40km |
| Interface | LC duplex |
| Optical Components | 4x DFB |
| Media | SMF |
| DOM Support | Yes |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Protocols | MSA Compliant |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CFP housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 40km route. Keep the interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Ciena Compatibility and Factory Testing
The module is checked for host recognition as CFP-ER4-40KM, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 103.1 Gbp, wavelength 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm, rated reach 40km.
Ordering Information
Quote HT part number CFP-ER4-100G together with OEM reference CFP-ER4-40KM and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each CFP-ER4-40KM compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Ciena transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CFP-ER4-40KM, not an original Ciena-branded module.
Which fiber and connector are required?
Use the specified optical connector with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
