CFP-SR10-100GGeneric CFP-SR10-100G Compatible 100G CFP SR10 Transceiver Module
The CFP-SR10-100G compatible module serves equipment requiring a 100G CFP interface with 850nm optics and a 150m rating. Connection is through its specified interface. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: CFP-SR10-100GHT Part Number: CFP-SR10-100G
Product Highlights
- Compatible alternative to Generic CFP-SR10-100G
- 100G connectivity at 103.1 Gbp
- Optical wavelength: 850nm
- Specified reach: 150m
- MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Generic | CFP-SR10-100G |
|---|---|
| Manufacturer | HT |
| HT Part Number | CFP-SR10-100G |
| Form Factor | CFP |
| Max Data Rate | 103.1 Gbp |
| Wavelength | 850nm |
| Max Cable Distance | 150m |
| Interface | MTP/MPO-24 |
| Optical Components | 10x VCSEL |
| Media | MMF |
| DOM Support | Yes |
| Modulation (Electrical) | 10x 10G-NRZ |
| Modulation (Optical) | 10x 10G-NRZ |
| Protocols | MSA Compliant |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CFP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 150m reach. Keep the end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Generic Compatibility and Factory Testing
The module is checked for host recognition as CFP-SR10-100G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 103.1 Gbp, wavelength 850nm, rated reach 150m.
Ordering Information
Use CFP-SR10-100G as the compatibility cross-reference and CFP-SR10-100G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use the specified optical connector with MMF. The specified maximum reach is 150m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
