CW47-SFP1G-120-IGeneric CW47-SFP1G-120-I Compatible 1G SFP Transceiver Module
The CW47-SFP1G-120-I compatible module serves equipment requiring a 1G SFP interface with 1470nm optics and a 120km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: CW47-SFP1G-120-IHT Part Number: CW47-SFP1G-120-I
Product Highlights
- Compatible alternative to Generic CW47-SFP1G-120-I
- 1G connectivity at 1.25Gbps
- Optical wavelength: 1470nm
- Specified reach: 120km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | CW47-SFP1G-120-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP |
| Max Data Rate | 1.25Gbps |
| Wavelength | 1470nm |
| Max Cable Distance | 120km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | APD |
| Receiver Sensitivity | <-31dBm |
| SMSR | 30dB |
| TX Power | 0~5dBm |
| RX Power | -31~-10dBm |
| Power Consumption | ≤1.5W |
| Power Budget | 31dB |
| EMC (Electro Magnetic Comnatihility) | Supported |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | SFP MSA,SFF-8472,IEEE 802.3z |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this 1470nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 120km using the complete channel rather than fiber distance alone.
Generic Compatibility and Factory Testing
Factory verification starts with the expected CW47-SFP1G-120-I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is <-31dBm; the stated optical power budget is 31dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 1.25Gbps, wavelength 1470nm, rated reach 120km.
Ordering Information
Use CW47-SFP1G-120-I as the compatibility cross-reference and CW47-SFP1G-120-I as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 120km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
