10/100BASE-T SFPCisco CWDM-SFP10G-1350-20 Compatible 10G SFP+ Transceiver Module
Built for hosts recognizing CWDM-SFP10G-1350-20, this HT-manufactured SFP+ module delivers 10G transmission at 1350nm. Its rated reach is 20km, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CWDM-SFP10G-1350-20HT Part Number: CW-SFP10G20-35
Product Highlights
- Compatible alternative to Cisco CWDM-SFP10G-1350-20
- 10G connectivity at 11.0957Gbps
- Optical wavelength: 1350nm
- Specified reach: 20km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Cisco Compatible | CWDM-SFP10G-1350-20 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CW-SFP10G20-35 |
| Form Factor | SFP+ |
| Max Data Rate | 11.0957Gbps |
| Wavelength | 1350nm |
| Max Cable Distance | 20km |
| Connector | Duplex LC |
| Media | SMF |
| Power Consumption | 1.2W |
| Packaging Technology | TO |
| Optical Components | DFB CWDM |
| DOM Support | Yes |
| TX Power | 1~6dBm |
| RX Power | -14.4~0dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Receiver Sensitivity | <-14.4dBm |
| Modulation | NRZ |
| Extinction Ratio | >3.5dB |
| Protocols | SFP+ MSA Compliant, CPRI, eCPRI, ITU-T G.652 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1350nm, then include their insertion loss in the 20km power budget. A nearby channel is not a substitute for the specified wavelength.
Cisco Compatibility and Factory Testing
Factory verification starts with the expected CWDM-SFP10G-1350-20 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 1~6dBm; receiver sensitivity is <-14.4dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 11.0957Gbps, wavelength 1350nm, rated reach 20km.
Ordering Information
Use CWDM-SFP10G-1350-20 as the compatibility cross-reference and CW-SFP10G20-35 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CWDM-SFP10G-1350-20, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 20km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
