DW-SFP25G10-20-IGeneric DW-SFP25G10-20-I Compatible 25G SFP28 Transceiver Module
Built for hosts recognizing DW-SFP25G10-20-I, this HT-manufactured SFP28 module delivers 25G transmission at 1561.42nm. Its rated reach is 10km, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: DW-SFP25G10-20-IHT Part Number: DW-SFP25G10-20-I
Product Highlights
- Compatible alternative to Generic DW-SFP25G10-20-I
- 25G connectivity at 25.78Gbps
- Optical wavelength: 1561.42nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | DW-SFP25G10-20-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP28 |
| Max Data Rate | 25.78Gbps |
| Wavelength | 1561.42nm |
| Max Cable Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | APD |
| TX Power | 0~5dBm |
| Receiver Sensitivity | ＜-14dBm |
| Power Budget | 14dB |
| Receiver Overload | -5dBm |
| Power Consumption | ≤2W |
| Extinction Ratio | ＞6dB |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| CDR (Clock and Data Recovery) | TX and RX |
| FEC Function | Not Supported |
| Protocols | SFF-8431, SFF-8472, RoHS |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this 1561.42nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 10km using the complete channel rather than fiber distance alone.
Generic Compatibility and Factory Testing
Compatibility testing for DW-SFP25G10-20-I combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is ＜-14dBm; the stated optical power budget is 14dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 25.78Gbps, wavelength 1561.42nm, rated reach 10km.
Ordering Information
Use DW-SFP25G10-20-I as the compatibility cross-reference and DW-SFP25G10-20-I as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each DW-SFP25G10-20-I compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
