DW2-QSFP100G80-2122Generic DW2-QSFP100G80-2122 Compatible 100G QSFP28 Transceiver Module
Built for hosts recognizing DW2-QSFP100G80-2122, this HT-manufactured QSFP28 module delivers 100G transmission at 1560.61nm,1559.79nm. Its rated reach is 80km with EDFA and TDCM, with Duplex CS/UPC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: DW2-QSFP100G80-2122HT Part Number: DW2-QSFP100G80-2122
Product Highlights
- Compatible alternative to Generic DW2-QSFP100G80-2122
- 100G connectivity at 100Gbps (2x50G)
- Optical wavelength: 1560.61nm,1559.79nm
- Specified reach: 80km with EDFA and TDCM
- Duplex CS/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 85°C (32 to 185°F)
Specifications
| HT Part Number | DW2-QSFP100G80-2122 |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | 100Gbps (2x50G) |
| Wavelength | 1560.61nm,1559.79nm |
| Max Cable Distance | 80km with EDFA and TDCM |
| Connector | Duplex CS/UPC |
| Cable Type | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 85°C (32 to 185°F) |
| TX Power | -1~4dBm |
| Minimum Receiver Power | -13dBm |
| Power Budget | 12dBm |
| Receiver overload | ≥5dBm |
| Power Consumption | 5W |
| Extinction Ratio | 6dB (Typ.) |
| Modulation Format | PAM4 |
| Protocols | IEEE 802.3bm, QSFP28 MSA, SFF-8636, SFF-8024 |
| Application | DCI, 100G Ethernet Metro-Access over DWDM,Campus and Enterprise Links |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this 1560.61nm,1559.79nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 80km with EDFA and TDCM using the complete channel rather than fiber distance alone.
Generic Compatibility and Factory Testing
Compatibility testing for DW2-QSFP100G80-2122 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~4dBm; the stated optical power budget is 12dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 100Gbps (2x50G), wavelength 1560.61nm,1559.79nm, rated reach 80km with EDFA and TDCM.
Ordering Information
Use DW2-QSFP100G80-2122 as the compatibility cross-reference and DW2-QSFP100G80-2122 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each DW2-QSFP100G80-2122 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex CS/UPC with SMF. The specified maximum reach is 80km with EDFA and TDCM, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
