DWDM-SFP10G-40-IGeneric DWDM-SFP10G-40-I Compatible 10G SFP+ Transceiver Module
Built for hosts recognizing DWDM-SFP10G-40-I, this HT-manufactured SFP+ module delivers 10G transmission at 1560.61nm. Its rated reach is 40km on OS2, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: DWDM-SFP10G-40-IHT Part Number: DW-SFP10G40-21-I
Product Highlights
- Compatible alternative to Generic DWDM-SFP10G-40-I
- 10G connectivity at 10 Gbps
- Optical wavelength: 1560.61nm
- Specified reach: 40km on OS2
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | DW-SFP10G40-21-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Data Rate | 10 Gbps |
| Wavelength | 1560.61nm |
| Max. Data Rate | 11.3Gbps |
| Wavelength | 1563.86nm |
| Max. Cable Distance | 40km@OS2 |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | DWDM EML |
| Receiver Type | PIN |
| TX Power | -1~4dBm |
| Minimum Receiver Power | -15dBm |
| Power Budget | 14dB |
| Receiver Overload | 0dBm |
| Max. Power Consumption | 1.9W |
| Extinction Ratio | >6dB |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | SFP+ MSA, SFF-8431, SFF 8472, 10GBASE-ER/EW, SDH STM64 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1560.61nm, then include their insertion loss in the 40km on OS2 power budget. A nearby channel is not a substitute for the specified wavelength.
Generic Compatibility and Factory Testing
Factory verification starts with the expected DWDM-SFP10G-40-I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~4dBm; the stated optical power budget is 14dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10 Gbps, wavelength 1560.61nm, rated reach 40km on OS2.
Ordering Information
Quote HT part number DW-SFP10G40-21-I together with OEM reference DWDM-SFP10G-40-I and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 40km on OS2, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
