10/100BASE-T SFPExtreme Networks DWDM-SFP10G-60.61 Compatible 10G SFP+ Transceiver Module 40km on OS2
The DWDM-SFP10G-60.61 compatible module serves equipment requiring a 10G SFP+ interface with 1560.61nm optics and a 40km on OS2 rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: DWDM-SFP10G-60.61HT Part Number: DW-SFP10G40-21
Product Highlights
- Compatible alternative to Extreme Networks DWDM-SFP10G-60.61
- 10G connectivity at 10Gbps
- Optical wavelength: 1560.61nm
- Specified reach: 40km on OS2
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Extreme Networks Compatible | DWDM-SFP10G-60.61 |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP10G40-21 |
| Form Factor | SFP+ |
| Max Data Rate | 10Gbps |
| Wavelength | 1560.61nm |
| Max Cable Distance | 40km@OS2 |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML DWDM |
| Receiver Type | PIN |
| TX Power | -1~4dBm |
| Receiver Sensitivity | <-15dBm |
| Power Budget | 14dB |
| Receiver Overload | 0dBm |
| Max. Power Consumption | 1.6W |
| Extinction Ratio | >6dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | SFP+ MSA, CPRI, eCPRI, SFF-8472, SFF-8431 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1560.61nm, then include their insertion loss in the 40km on OS2 power budget. A nearby channel is not a substitute for the specified wavelength.
Extreme Networks Compatibility and Factory Testing
Compatibility testing for DWDM-SFP10G-60.61 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~4dBm; receiver sensitivity is <-15dBm; the stated optical power budget is 14dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10Gbps, wavelength 1560.61nm, rated reach 40km on OS2.
Ordering Information
Use DWDM-SFP10G-60.61 as the compatibility cross-reference and DW-SFP10G40-21 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Extreme Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies DWDM-SFP10G-60.61, not an original Extreme Networks-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 40km on OS2, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
