EX-SFP-25GE-CWE27-30Juniper Networks EX-SFP-25GE-CWE27-30 Compatible 25G SFP28 Transceiver Module
The EX-SFP-25GE-CWE27-30 compatible module serves equipment requiring a 25G SFP28 interface with 1270nm optics and a 30km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: EX-SFP-25GE-CWE27-30HT Part Number: CW-SFP25G30-27
Product Highlights
- Compatible alternative to Juniper Networks EX-SFP-25GE-CWE27-30
- 25G connectivity at 25.78Gbps
- Optical wavelength: 1270nm
- Specified reach: 30km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Juniper Networks Compatible | EX-SFP-25GE-CWE27-30 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CW-SFP25G30-27 |
| Form Factor | SFP28 |
| Max Data Rate | 25.78Gbps |
| Wavelength | 1270nm |
| Max Cable Distance | 30km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DML CWDM |
| Receiver Type | APD |
| TX Power | 0~5dBm |
| Receiver Sensitivity | <-13.5dBm |
| Power Consumption | 1.5W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| CDR | TX and RX |
| Power Budget | 13.5dB |
| FEC Function | Supported |
| Protocols | MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 25G interface configuration must match the remote equipment; sharing a SFP28 housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1270nm, then include their insertion loss in the 30km power budget. A nearby channel is not a substitute for the specified wavelength.
Juniper Networks Compatibility and Factory Testing
Factory verification starts with the expected EX-SFP-25GE-CWE27-30 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is <-13.5dBm; the stated optical power budget is 13.5dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 25.78Gbps, wavelength 1270nm, rated reach 30km.
Ordering Information
When ordering, specify EX-SFP-25GE-CWE27-30, CW-SFP25G30-27, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies EX-SFP-25GE-CWE27-30, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 30km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
