Dell (Force10) CBL-10GSFP-DAC-6M Compatible 10G SFP+ Passive Copper Twinax Cable, 6m (20ft)

Product Highlights

• Compatible alternative to Dell (Force10) CBL-10GSFP-DAC-6M
• 10G connectivity at 10Gbps
• Interface configuration: SFP+ to SFP+
• Fixed length and part number: 6m (20ft), (Force10) CBL-10GSFP-DAC-6M
• Cable construction: Passive Twinax
• Conductor specification: 24AWG
• Maximum power consumption: ≤0.1W
• Minimum bend radius: 30mm

Specifications

Power and Thermal Planning

The rated power consumption is ≤0.1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Position Within the Length Range

(Force10) CBL-10GSFP-DAC-6M occupies the middle of this family between (Force10) CBL-10GSFP-DAC-5M at 5m (16ft) and (Force10) CBL-10GSFP-DAC-7M at 7m (23ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Structured Pathways and Serviceability

Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this assembly, the listed conductor specification is 24AWG; the minimum bend radius is 30mm; the stated power consumption is ≤0.1W; the jacket material is PVC (OFNR).

Cable Construction and Routing

This assembly uses 24AWG conductors, PVC (OFNR) jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Network and Protocol Considerations

The intended application is 10G Ethernet. Listed interface and protocol references include 1x InfiniBand QDR, DDR, SDR, 10 Gigabit Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

Passive Copper Operation

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

Length Selection and Installation Planning

Measure twice before deploying this 6m (20ft) cable: once along the planned route and again after accounting for service access. The objective is adequate reach without a concealed surplus. Support the complete copper assembly and both connector housings, preserve front-panel clearance and check that nearby power cords or sharp hardware cannot damage the jacket. Within this family, (Force10) CBL-10GSFP-DAC-5M is shorter at 5m (16ft), while (Force10) CBL-10GSFP-DAC-7M is the next longer choice at 7m (23ft); comparing those two boundaries helps avoid both tension and unnecessary slack.

Ordering Information

Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. This page’s fixed configuration is 6m (20ft); another length must be quoted under its corresponding part number.

Dell Compatibility and Factory Testing

Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. The check includes link stability and diagnostic indications, followed by a final inspection of both ends.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.

Quality Assurance and Packaging

After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Neutral packaging and customer-specific packing documentation are available on request.

Frequently Asked Questions