J9144AHPE J9144A Compatible XFP X2 10GBASE-LRM Transceiver Module
Built for hosts recognizing J9144A, this HT-manufactured X2 module delivers XFP transmission at 1310nm. Its rated reach is 220m, with SC duplex as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: J9144AHT Part Number: J9144A
Product Highlights
- Compatible alternative to HPE J9144A
- XFP connectivity at 10Gbps
- Optical wavelength: 1310nm
- Specified reach: 220m
- SC duplex / MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HPE Compatible | J9144A |
|---|---|
| Manufacturer | HT |
| HT Part Number | J9144A |
| Form Factor | X2 |
| Max. Data Rate | 10Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 220m |
| Connector | SC duplex |
| Transmitter Type | FP 1310nm |
| Media | MMF |
| DOM Support | Yes |
| TX Power | -6.5~-0.5dBm |
| Receiver Sensitivity | < -14.4dBm |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The SC duplex interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The XFP interface configuration must match the remote equipment; sharing a X2 housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 220m reach. Keep the SC duplex end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
HPE Compatibility and Factory Testing
The module is checked for host recognition as J9144A, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~-0.5dBm; receiver sensitivity is < -14.4dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10Gbps, wavelength 1310nm, rated reach 220m.
Ordering Information
Use J9144A as the compatibility cross-reference and J9144A as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each J9144A compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original HPE transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies J9144A, not an original HPE-branded module.
Which fiber and connector are required?
Use SC duplex with MMF. The specified maximum reach is 220m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
