NVIDIA/Mellanox MCP1600-E001E30 Compatible 100G QSFP28 4 x 25G NRZ Infiniband EDR Passive Copper Twinax Cable, 1m (3ft)

Product Highlights

• Compatible alternative to NVIDIA/Mellanox MCP1600-E001E30
• 100G connectivity at 100Gbps
• Interface configuration: QSFP28 to QSFP28
• Fixed length and part number: 1m (3ft), MCP1600-E001E30
• Cable construction: Passive Twinax
• Conductor specification: 30AWG
• Maximum power consumption: ≤0.5W
• Minimum bend radius: 33.5mm

Specifications

NVIDIA OEM Reference

NVIDIA describes MCP1600 QSFP28 passive copper cables as four high-speed copper pairs operating at up to 25GbE per pair, with EEPROM product identification readable by the host. Its documentation distinguishes shorter no-FEC versions from longer RS-FEC versions, with specific variants at 2.5m and 3m. Check the exact suffix rather than selecting by length alone.

Network and Protocol Considerations

The intended application is InfiniBand EDR. Listed interface and protocol references include IEEE 802.3bj, QSFP28 MSA, SFF-8665, SFF-8436. Confirm that the host firmware and port configuration support the same operating mode.

Passive Copper Operation

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

Length Selection and Installation Planning

At 1m (3ft), MCP1600-E001E30 is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.

Position Within the Length Range

MCP1600-E001E30 occupies the middle of this family between MCP1600-E00AE30 at 0.5m (2ft) and MCP1600-E01AE30 at 1.5m (5ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Structured Pathways and Serviceability

Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this assembly, the listed conductor specification is 30AWG; the minimum bend radius is 33.5mm; the stated power consumption is ≤0.5W; the jacket material is PVC (OFNR).

Signal and Lane Configuration

The listed modulation format is 4x 25G-NRZ to 4x 25G-NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

Power and Thermal Planning

The rated power consumption is ≤0.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Cable Construction and Routing

This assembly uses 30AWG conductors, PVC (OFNR) jacket, minimum bend radius 33.5mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Ordering Information

Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. Keep MCP1600-E001E30 associated with 1m (3ft) throughout the order and receiving record.

NVIDIA/Mellanox Compatibility and Factory Testing

Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. Where supported by the host, link stability and diagnostic indications are reviewed together with the established link.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.

Quality Assurance and Packaging

After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Volume orders can include customer references on the labels and carton list.

Frequently Asked Questions