10/100BASE-T SFPNVIDIA/Mellanox MMS4X00-NS400 Compatible 400G Single-port OSFP RHS/Flat Top DR4L Transceiver Module
The MMS4X00-NS400 compatible module serves equipment requiring a 400G Single-port OSFP RHS/Flat Top interface with 1310nm optics and a 100m rating. Connection is through MPO-12/APC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: MMS4X00-NS400HT Part Number: OSFP-DR4L-400G-FL
Product Highlights
- Compatible alternative to NVIDIA/Mellanox MMS4X00-NS400
- 400G connectivity at 425Gbps (4x106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 100m
- MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| NVIDIA/Mellanox Ethernet Compatible | MMS4X00-NS400 |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP-DR4L-400G-FL |
| Form Factor | Single-port OSFP RHS/Flat Top |
| Max. Data Rate | 425Gbps (4x106.25Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 100m |
| Connector | MPO-12/APC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -2.9~4dBm |
| Minimum Receiver Power | -5.9dBm |
| Power Budget | 3dB |
| Receiver Overload | 4.0dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x100G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Yes |
| Core Size | 9/125um |
| Packaging Technology | COB |
| MTBF | 4974730 Hours (@40°C, 60% CL)2542973 Hours (@40°C, 90% CL)3639584 Hours (@50°C, 60% CL)1750006 Hours (@50°C, 90% CL)2349812 Hours (@60°C, 60% CL)1061485 Hours (@60°C, 90% CL) |
| Application | 400G Ethernet |
| Protocols | OSFP MSA Rev. 5.0, CMIS Rev. 4.0, IEEE Std 802.3bs-2017, IEEE Std 802.3ck-2022 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a Single-port OSFP RHS/Flat Top housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 100m. Inspect every MPO-12/APC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
NVIDIA/Mellanox Compatibility and Factory Testing
Factory verification starts with the expected MMS4X00-NS400 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -2.9~4dBm; the stated optical power budget is 3dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 425Gbps (4x106.25Gbps), wavelength 1310nm, rated reach 100m.
Ordering Information
When ordering, specify MMS4X00-NS400, OSFP-DR4L-400G-FL, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original NVIDIA/Mellanox transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies MMS4X00-NS400, not an original NVIDIA/Mellanox-branded module.
Which fiber and connector are required?
Use MPO-12/APC with SMF. The specified maximum reach is 100m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
