10/100BASE-T SFPCisco OSFP-2LR4L-800G Compatible 800G Twin-port OSFP IHS/Closed Finned Top Transceiver Module
Built for hosts recognizing OSFP-2LR4L-800G, this HT-manufactured Twin-port OSFP IHS/Closed Finned Top module delivers 800G transmission at 1270nm, 1290nm, 1310nm, 1330nm. Its rated reach is 6km, with Dual Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: OSFP-2LR4L-800GHT Part Number: OSFP-2LR4L-800G
Product Highlights
- Compatible alternative to Cisco OSFP-2LR4L-800G
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1270nm, 1290nm, 1310nm, 1330nm
- Specified reach: 6km
- Dual Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP-2LR4L-800G |
|---|---|
| Manufacturer | HT |
| Form Factor | Twin-port OSFP IHS/Closed Finned Top |
| Max. Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1270nm, 1290nm, 1310nm, 1330nm |
| Max. Cable Distance | 6km |
| Connector | Dual Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -2.7~5.1dBm |
| Minimum Receiver Power | -9dBm |
| Power Budget | 6.3dB |
| Receiver Overload | 5.1dBm |
| Max. Power Consumption | 15W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x 100G-PAM4 |
| Modulation (Optical) | Dual 4x 100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Inbuilt FEC | No |
| Protocols | OSFP MSA, CMIS v5.1/v5.2, IEEE 802.3cu and 802.3ck |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Twin-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 6km route. Keep the Dual Duplex LC/UPC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Cisco Compatibility and Factory Testing
Compatibility testing for OSFP-2LR4L-800G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -2.7~5.1dBm; the stated optical power budget is 6.3dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1270nm, 1290nm, 1310nm, 1330nm, rated reach 6km.
Ordering Information
Use OSFP-2LR4L-800G as the compatibility cross-reference and OSFP-2LR4L-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-2LR4L-800G, not an original Cisco-branded module.
Which fiber and connector are required?
Use Dual Duplex LC/UPC with SMF. The specified maximum reach is 6km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
