10/100BASE-T SFPJuniper Networks OSFP-2X400G-LR4-P Compatible 800G Twin-port OSFP IHS/Closed Finned Top Transceiver Module
Built for hosts recognizing OSFP-2X400G-LR4-P, this HT-manufactured Twin-port OSFP IHS/Closed Finned Top module delivers 800G transmission at 1271nm, 1291nm, 1311nm and 1331nm. Its rated reach is 10km, with Dual Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: OSFP-2X400G-LR4-PHT Part Number: OSFP800-2LR4-A2
Product Highlights
- Compatible alternative to Juniper Networks OSFP-2X400G-LR4-P
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm and 1331nm
- Specified reach: 10km
- Dual Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Juniper Networks Compatible | OSFP-2X400G-LR4-P |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP800-2LR4-A2 |
| Form Factor | Twin-port OSFP IHS/Closed Finned Top |
| Max. Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm and 1331nm |
| Max. Cable Distance | 10km |
| Connector | Dual Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | Siphotonics PIN PD |
| TX Power | -2.7~5.1dBm |
| Minimum Receiver Power | -9dBm |
| Power Budget | 6.3dB |
| Receiver Overload | 5.1dBm |
| Max. Power Consumption | 18W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x 100G-PAM4 |
| Modulation (Optical) | Dual 4x 100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Inbuilt FEC | No |
| Packaging Technology | COB (Chip on Board) Packaging |
| Modulation Format | PAM4 |
| Protocols | OSFP MSA HW Rev 4.1, CMIS Rev 5.0, MSA- 2x400G-LR4-10, IEEE P802.3ck D3.0 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Twin-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every Dual Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Juniper Networks Compatibility and Factory Testing
Compatibility testing for OSFP-2X400G-LR4-P combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -2.7~5.1dBm; the stated optical power budget is 6.3dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1271nm, 1291nm, 1311nm and 1331nm, rated reach 10km.
Ordering Information
When ordering, specify OSFP-2X400G-LR4-P, OSFP800-2LR4-A2, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-2X400G-LR4-P, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Dual Duplex LC/UPC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
