10/100BASE-T SFPArista Networks OSFP-400G-SR8 Compatible 400G Single-port OSFP IHS/Finned Top SR8 Transceiver Module
Built for hosts recognizing OSFP-400G-SR8, this HT-manufactured Single-port OSFP IHS/Finned Top module delivers 400G transmission at 850nm. Its rated reach is 100m on OM4, with MPO-16/APC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: OSFP-400G-SR8HT Part Number: OSFP-SR8-400G
Product Highlights
- Compatible alternative to Arista Networks OSFP-400G-SR8
- 400G connectivity at 425Gbps
- Optical wavelength: 850nm
- Specified reach: 100m on OM4
- MPO-16/APC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Arista Networks Compatible | OSFP-400G-SR8 |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP-SR8-400G |
| Form Factor | Single-port OSFP IHS/Finned Top |
| Max. Data Rate | 425Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 100m@OM4 |
| Connector | MPO-16/APC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -6.5~4dBm |
| Minimum Receiver Power | -8.4dBm |
| Power Budget | 1.9dB |
| Receiver Overload | 4.0dBm |
| Max. Power Consumption | 10W |
| Extinction Ratio | 3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 8x50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | No |
| Core Size | 50μm |
| Packaging Technology | COB |
| MTBF | 684931 Hours (@50°C , 60% CL)273972 Hours (@50°C , 90% CL) |
| Application | 400G Ethernet |
| Protocols | OSFP MSA, CMIS 4.1, IEEE 802.3cd |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-16/APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a Single-port OSFP IHS/Finned Top housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 100m on OM4 figure applies only under suitable cabling conditions. Inspect every MPO-16/APC mating point and match the remote optical standard.
Arista Networks Compatibility and Factory Testing
The module is checked for host recognition as OSFP-400G-SR8, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~4dBm; the stated optical power budget is 1.9dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 425Gbps, wavelength 850nm, rated reach 100m on OM4.
Ordering Information
When ordering, specify OSFP-400G-SR8, OSFP-SR8-400G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Arista Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-400G-SR8, not an original Arista Networks-branded module.
Which fiber and connector are required?
Use MPO-16/APC with MMF. The specified maximum reach is 100m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
