QSFP-100G-ESR4-SCisco QSFP-100G-ESR4-S Compatible 100G QSFP28 ESR4 Transceiver Module
Built for hosts recognizing QSFP-100G-ESR4-S, this HT-manufactured QSFP28 module delivers 100G transmission at 850nm. Its rated reach is 200m on OM3 / 300m on OM4, with MTP/MPO-12 as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-100G-ESR4-SHT Part Number: QSFP-ESR4-100G
Product Highlights
- Compatible alternative to Cisco QSFP-100G-ESR4-S
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 850nm
- Specified reach: 200m on OM3 / 300m on OM4
- MTP/MPO-12 / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Cisco Compatible | QSFP-100G-ESR4-S |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-ESR4-100G |
| Form Factor | QSFP28 |
| Max Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelengths | 850nm |
| Max Cable Distance | 200m@OM3/300m@OM4 |
| Connector | MTP/MPO-12 |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -4~4dBm |
| RX Power | -12~2.4dBm |
| Power Consumption | ≤2.5W |
| Extinction Ratio | >2dB |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Supported |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Core Size | 50um/125um |
| Packaging Technology | COB Packaging |
| Protocols | IEEE 802.3bm, QSFP28 MSA, SFF-8665, SFF-8636, SFF-8679 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 200m on OM3 / 300m on OM4 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-12 mating point and match the remote optical standard.
Cisco Compatibility and Factory Testing
Compatibility testing for QSFP-100G-ESR4-S combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4~4dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 850nm, rated reach 200m on OM3 / 300m on OM4.
Ordering Information
Use QSFP-100G-ESR4-S as the compatibility cross-reference and QSFP-ESR4-100G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-100G-ESR4-S, not an original Cisco-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 with MMF. The specified maximum reach is 200m on OM3 / 300m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
