10/100BASE-T SFPCisco QSFP-200G-SR4-S Compatible 200G QSFP56 SR4 Transceiver Module
This Cisco QSFP-200G-SR4-S compatible transceiver provides 200G connectivity in a hot-swappable QSFP56 package. Its optical design operates at 850nm for up to 70m on OM3 / 100m on OM4, using MPO-12/UPC. Complete parameters and related OEM references help structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: QSFP-200G-SR4-SHT Part Number: QSFP-SR4-200G
Product Highlights
- Compatible alternative to Cisco QSFP-200G-SR4-S
- 200G connectivity at 200Gbps
- Optical wavelength: 850nm
- Specified reach: 70m on OM3 / 100m on OM4
- MPO-12/UPC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Cisco Compatible | QSFP-200G-SR4-S |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-SR4-200G |
| Form Factor | QSFP56 |
| Max. Data Rate | 200Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 70m@OM3/100m@OM4 |
| Connector | MPO-12/UPC |
| Media | MMF |
| Transmitter Type | VCSEL 850nm |
| Receiver Type | PIN |
| TX Power | -3~3dBm |
| Minimum Receiver Power | -6.5dBm |
| Power Budget | 3.5dBm |
| Receiver Overload | 5dBm |
| Max. Power Consumption | 4.35W |
| Extinction Ratio | 3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x50G-PAM4 |
| Modulation (Optical) | 4x50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| FEC Function | Support RS-FEC |
| Protocols | QSFP56 MSA, CMIS Rev 4.0, IEEE 802.3bs, SFF-8665, RoHS 10 |
| Application | 200G Ethernet, Data centers Interconnect, High performance computing |
| BER | 5E-10 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12/UPC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 200G interface configuration must match the remote equipment; sharing a QSFP56 housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 70m on OM3 / 100m on OM4 reach. Keep the MPO-12/UPC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Cisco Compatibility and Factory Testing
Compatibility testing for QSFP-200G-SR4-S combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3~3dBm; the stated optical power budget is 3.5dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 200Gbps, wavelength 850nm, rated reach 70m on OM3 / 100m on OM4.
Ordering Information
Quote HT part number QSFP-SR4-200G together with OEM reference QSFP-200G-SR4-S and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each QSFP-200G-SR4-S compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-200G-SR4-S, not an original Cisco-branded module.
Which fiber and connector are required?
Use MPO-12/UPC with MMF. The specified maximum reach is 70m on OM3 / 100m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
