10/100BASE-T SFPBroadcom QSFP-400G-AE Compatible 400G QSFP112 4 x 100G PAM4 Active Electrical Cable
A 400G direct-attached link depends on the correct host identity, interface mode and physical length. This page covers the Broadcom QSFP-400G-AE compatible AEC series in QSFP112 to QSFP112, including 1m (3ft) and 3m (10ft). Each documented length-specific OEM reference is linked separately where an individual product page is available.
Series Part Number: QSFP-400G-AEHT Part Number: QSFP-400G-AE
Product Highlights
- HT-manufactured compatible alternative for Broadcom QSFP-400G-AE
- 400G aggregate connectivity at 400Gbps
- Interface configuration: QSFP112 to QSFP112
- Active DAC (AEC) / Copper
- Length configurations covered: 1m (3ft) and 3m (10ft)
- Conductor specification: 32AWG
- Power consumption: <8W Per End
Available Lengths and Corresponding Part Numbers
The documented series configuration is 1m (3ft) and 3m (10ft). Use the relevant OEM reference below together with the HT identity and required length when requesting a quotation. If another length carries a different OEM part number, it must be reviewed and ordered as that distinct configuration.
Compatible OEM Part Numbers
- QSFP-400G-AE01
Specifications
| HT Part Number | QSFP-400G-AE |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP112 to QSFP112 |
| Max. Data Rate | 400Gbps |
| Media | Copper |
| Cable Type | Active DAC (AEC) |
| Minimum Bend Radius | 26.5mm |
| Wire AWG | 32AWG |
| Cable Length Options Covered | 1m (3ft) and 3m (10ft) |
| Jacket Material | PET |
| Power Consumption | <8W Per End |
| Modulation Format | 4x 100G-PAM4 |
| DDM/DOM | Supported |
| Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | QSFP112 MSA, IEEE 802.3ck 400GBase-CR4, CMIS 5.0 |
Applications and Deployment
Active electrical cables use signal recovery or retiming to support demanding high-speed electrical links. Deployment should begin with host support for the exact AEC configuration, followed by checks of per-end power, cooling and breakout operation. The two ends and cable are engineered and tested as one assembly. For this series, the listed interface is QSFP112 to QSFP112 and the aggregate rate is 400G.
Broadcom Compatibility and Factory Testing
Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Cable Construction and Routing
The specification table records the conductor specification is 32AWG; the jacket material is PET; the minimum bend radius is 26.5mm; the power consumption is <8W Per End. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.
Structured Pathways and Serviceability
Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this series, keep the interface rate, AEC construction and length-specific OEM reference together throughout that review.
Ordering Information
Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QSFP-400G-AE identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Frequently Asked Questions
Is this an original Broadcom cable?
No. It is an HT-manufactured compatible cable for equipment that specifies QSFP-400G-AE, not an original Broadcom-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
Does this AEC cable require separate modules at each end?
No. The connector ends and cable form one complete direct-attach assembly. The ends are not detachable standalone transceivers, and the complete product is tested together.
What information helps confirm compatibility?
Provide the equipment manufacturer and model, port type, hardware revision and software release, together with the required OEM reference, length and quantity. Breakout projects should also identify the intended lane configuration.
