10/100BASE-T SFPGeneric QSFP-56G-AO Compatible 56G QSFP+ Active Optical Cable for Generic Switches
This Generic QSFP-56G-AO compatible cable series provides 待分类 connectivity through a direct-attach configuration. It is a complete optical assembly with permanently attached ends and integrated fiber. The page brings together the series specifications, compatibility guidance and direct links to the individual length and OEM part-number pages used for ordering.
Series Part Number: QSFP-56G-AOHT Part Number: QSFP-56G-AO
Product Highlights
- HT-manufactured compatible alternative for Generic QSFP-56G-AO
- 待分类 aggregate connectivity at FDR 56Gbps
- AOC
- Length configurations covered: 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft)
Available Lengths and Corresponding Part Numbers
The documented configurations are 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.
Compatible OEM Part Numbers
- QSFP-56G-AO-1M3FT
- QSFP+ to QSFP+-High-Speed-AOC-2M7FT
- QSFP+ to QSFP+-High-Speed-AOC-3M10FT
- QSFP+ to QSFP+-High-Speed-AOC-5M16FT
- QSFP+ to QSFP+-High-Speed-AOC-10M33FT
- QSFP+ to QSFP+-High-Speed-AOC-15M49FT
- QSFP+ to QSFP+-High-Speed-AOC-20M66FT
- QSFP+ to QSFP+-High-Speed-AOC-25M82FT
- QSFP+ to QSFP+-High-Speed-AOC-30M98FT
- QSFP+ to QSFP+-High-Speed-AOC-50M164FT
- QSFP-56G-AO01
Specifications
| HT Part Number | QSFP-56G-AO |
|---|---|
| Manufacturer | HT |
| Connector Type | QSFP+ to QSFP+ |
| Data Rate | FDR 56Gbps |
| Minimum Bend Radius | 30mm |
| Cable Length Options Covered | 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft) |
| Jacket Material | OFNP |
| Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | 56G InfiniBand , 4x FDR, Fibre Channel |
Applications and Deployment
An AOC removes the separate module-and-fiber interfaces from a high-speed connection. Both optical ends remain attached to the cable, simplifying polarity control and connector handling. Host identification, wavelength plan, aggregate rate and any breakout configuration must still agree across the link. For this series, the listed interface is the stated interface and the aggregate rate is 待分类.
Generic Compatibility and Factory Testing
Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Cable Construction and Routing
The specification table records the jacket material is OFNP; the minimum bend radius is 30mm. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.
Structured Pathways and Serviceability
Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this series, keep the interface rate, AOC construction and length-specific OEM reference together throughout that review.
Ordering Information
Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QSFP-56G-AO identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Frequently Asked Questions
Is this an original Generic cable?
No. It is an HT-manufactured compatible cable for equipment that specifies QSFP-56G-AO, not an original Generic-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
Does this AOC cable require separate modules at each end?
No. The connector ends and cable form one complete direct-attach assembly. The ends are not detachable standalone transceivers, and the complete product is tested together.
What information helps confirm compatibility?
Provide the equipment manufacturer and model, port type, hardware revision and software release, together with the required OEM reference, length and quantity. Breakout projects should also identify the intended lane configuration.
