QSFP-ER4L-100G-D30NVIDIA/Mellanox QSFP-ER4L-100G-D30 Compatible 100G QSFP28 ER4L Transceiver Module
This NVIDIA/Mellanox QSFP-ER4L-100G-D30 compatible transceiver provides 100G connectivity in a hot-swappable QSFP28 package. Its optical design operates at 1310nm* for up to 30km on SMF, using LC duplex. Complete parameters and related OEM references help structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: QSFP-ER4L-100G-D30HT Part Number: QSFP-ER4L-100G-D30
Product Highlights
- Compatible alternative to NVIDIA/Mellanox QSFP-ER4L-100G-D30
- 100G connectivity at Dual Rate 103.1Gbps and 112Gbps
- Optical wavelength: 1310nm*
- Specified reach: 30km on SMF
- LC duplex / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Mellanox Compatible | QSFP-ER4L-100G-D30 |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-ER4L-100G-D30 |
| Form Factor | QSFP28 |
| Data Rate | Dual Rate 103.1Gbps and 112Gbps |
| Wavelength | 1310nm* |
| Max Cable Distance | 30km@SMF |
| Connector | LC duplex |
| Media | SMF |
| Transmitter Type | 4 x LAN WDM DML TOSA |
| Receiver Type | 4 x PIN ROSA |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| TX Power(100G) | -2.5~4.5dBm |
| Receiver Sensitivity(100G) | <-15dBm |
| TX Power(112G) | -1.5~4.5dBm |
| Receiver Sensitivity(112G) | <-14.5dBm |
| Power Consumption | 4.5W |
| Extinction Ratio | 4dB |
| Modulation Format | NRZ |
| CDR | TX and RX |
| Transmit and Dispersion Penalty | 2.5dB |
| Power Budget | 14.4dB |
| Packaging Technology | BOX Packaging |
| FEC Function** | Supported |
| Protocols | 100G Ethernet, 100G Telecom Connections, Infiniband QDR and DDR Interconnects |
| Application | 100GBASE Ethernet, Telecom, 5G Network Mid/Backhaul |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 30km on SMF. Inspect every LC duplex connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
NVIDIA/Mellanox Compatibility and Factory Testing
The module is checked for host recognition as QSFP-ER4L-100G-D30, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the stated optical power budget is 14.4dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate Dual Rate 103.1Gbps and 112Gbps, wavelength 1310nm*, rated reach 30km on SMF.
Ordering Information
When ordering, specify QSFP-ER4L-100G-D30, QSFP-ER4L-100G-D30, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each QSFP-ER4L-100G-D30 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original NVIDIA/Mellanox transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ER4L-100G-D30, not an original NVIDIA/Mellanox-branded module.
Which fiber and connector are required?
Use LC duplex with SMF. The specified maximum reach is 30km on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
