QSFP-ERL-100GH3C QSFP-ERL-100G Compatible 100G QSFP28 ERL Transceiver Module
Built for hosts recognizing QSFP-ERL-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 1310nm. Its rated reach is 25km, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-ERL-100GHT Part Number: QSFP-ERL-100G
Product Highlights
- Compatible alternative to H3C QSFP-ERL-100G
- 100G connectivity at 106.25Gbps
- Optical wavelength: 1310nm
- Specified reach: 25km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-ERL-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | 106.25Gbps |
| Wavelength | 1310nm |
| Max Cable Distance | 25km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | APD |
| TX Power | 0~5.6dBm |
| Minimum Receiver Power | -13.5dBm |
| Power Budget | 13.5dB |
| Receiver Overload | -2.6dBm |
| Power Consumption | <4W |
| Extinction Ratio | ＞5dB |
| DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 1x 100G-PAM4 |
| CDR (Clock and Data Recovery) | DSP |
| Packaging Technology | COB (Chip on Board) Packaging |
| Protocols | CEI-28G-VSR, QSFP28 MSA, SFF-8636 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 25km route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
H3C Compatibility and Factory Testing
The module is checked for host recognition as QSFP-ERL-100G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5.6dBm; the stated optical power budget is 13.5dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 106.25Gbps, wavelength 1310nm, rated reach 25km.
Ordering Information
Quote HT part number QSFP-ERL-100G together with OEM reference QSFP-ERL-100G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each QSFP-ERL-100G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ERL-100G, not an original H3C-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 25km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
