10/100BASE-T SFPGeneric QSFP-LR4-100GM Compatible 100G QSFP28 LR4 Transceiver Module
Built for hosts recognizing QSFP-LR4-100GM, this HT-manufactured QSFP28 module delivers 100G transmission at 1310nm. Its rated reach is 10km, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-LR4-100GMHT Part Number: QSFP-LR4-100GM
Product Highlights
- Compatible alternative to Generic QSFP-LR4-100GM
- 100G connectivity at Dual Rate 103.1Gbps and 112Gbps
- Optical wavelength: 1310nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-LR4-100GM |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | Dual Rate 103.1Gbps and 112Gbps |
| Wavelength | 1310nm |
| Max Cable Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | 4 x LAN WDM DML TOSA |
| Receiver Type | 4 x PIN ROSA |
| TX Power(100G) | -4.3~4.5dBm |
| Receiver Sensitivity(100G) | <-8.6dBm |
| TX Power(112G) | -0.6~4dBm |
| Receiver Sensitivity(112G) | <-8.4dBm |
| Transmit and Dispersion Penalty | 2.2dB |
| Power Budget | 6.3dB |
| Power Consumption | ≤3.5W |
| Extinction Ratio | >4dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Modulation Format | NRZ |
| Inbuilt FEC | No |
| Core Size | 9um/125um |
| Protocols | 100G Ethernet, 25G Ethernet, OTN OTU4 4I1-9D1F |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Generic Compatibility and Factory Testing
The module is checked for host recognition as QSFP-LR4-100GM, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the stated optical power budget is 6.3dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate Dual Rate 103.1Gbps and 112Gbps, wavelength 1310nm, rated reach 10km.
Ordering Information
Use QSFP-LR4-100GM as the compatibility cross-reference and QSFP-LR4-100GM as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
