10/100BASE-T SFPGeneric QSFP-SL4-100G Compatible 100G QSFP28 SL4 Transceiver Module
The QSFP-SL4-100G compatible module serves equipment requiring a 100G QSFP28 interface with 850nm optics and a 20m on OM3 / 30m on OM4 rating. Connection is through MPO-12. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: QSFP-SL4-100GHT Part Number: QSFP-SL4-100G
Product Highlights
- Compatible alternative to Generic QSFP-SL4-100G
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 850nm
- Specified reach: 20m on OM3 / 30m on OM4
- MPO-12 / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-SL4-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 850nm |
| Max Cable Distance | 20m@OM3/30m@OM4 |
| Connector | MPO-12 |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -8.4~2.4dBm |
| Minimum Receiver Power | -10.3dBm |
| Power Budget | 1.9dBm |
| Receiver Overload | 2.4dBm |
| Max Power Consumption | ≤2.5W |
| Extinction Ratio | ＞2dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Yes |
| Packaging Technology | COB Packaging |
| Core Size | 9um/125um |
| Protocols | IEEE 802.3bm |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12 interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 20m on OM3 / 30m on OM4 figure applies only under suitable cabling conditions. Inspect every MPO-12 mating point and match the remote optical standard.
Generic Compatibility and Factory Testing
Compatibility testing for QSFP-SL4-100G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.4~2.4dBm; the stated optical power budget is 1.9dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 850nm, rated reach 20m on OM3 / 30m on OM4.
Ordering Information
Use QSFP-SL4-100G as the compatibility cross-reference and QSFP-SL4-100G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use MPO-12 with MMF. The specified maximum reach is 20m on OM3 / 30m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
