10/100BASE-T SFPH3C QSFP-SL4-200G Compatible 200G QSFP56 SL4 Transceiver Module
Built for hosts recognizing QSFP-SL4-200G, this HT-manufactured QSFP56 module delivers 200G transmission at 850nm. Its rated reach is 30m, with MPO-12/UPC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-SL4-200GHT Part Number: QSFP-SL4-200G
Product Highlights
- Compatible alternative to H3C QSFP-SL4-200G
- 200G connectivity at 200Gbps
- Optical wavelength: 850nm
- Specified reach: 30m
- MPO-12/UPC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-SL4-200G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP56 |
| Max. Data Rate | 200Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 30m |
| Connector | MPO-12/UPC |
| Media | MMF |
| Transmitter Type | VCSEL 850nm |
| Receiver Type | PIN |
| TX Power | -3~3dBm |
| Minimum Receiver Power | -6.5dBm |
| Power Budget | 3.5dBm |
| Receiver Overload | 5dBm |
| Max. Power Consumption | 4.35W |
| Extinction Ratio | 3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x50G-PAM4 |
| Modulation (Optical) | 4x50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Support RS-FEC |
| Protocols | IEEE 802.3bs, QSFP56 MSA, SFF-8665, SFF-8636 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12/UPC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 200G interface configuration must match the remote equipment; sharing a QSFP56 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 30m figure applies only under suitable cabling conditions. Inspect every MPO-12/UPC mating point and match the remote optical standard.
H3C Compatibility and Factory Testing
The module is checked for host recognition as QSFP-SL4-200G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3~3dBm; the stated optical power budget is 3.5dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 200Gbps, wavelength 850nm, rated reach 30m.
Ordering Information
Use QSFP-SL4-200G as the compatibility cross-reference and QSFP-SL4-200G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-SL4-200G, not an original H3C-branded module.
Which fiber and connector are required?
Use MPO-12/UPC with MMF. The specified maximum reach is 30m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
