10/100BASE-T SFPExtreme QSFP-SR1.2-100G Compatible 100G QSFP28 SR1.2 Transceiver Module
Built for hosts recognizing QSFP-SR1.2-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 850/910nm. Its rated reach is 70m on OM3 / 100m on OM4 / 150m on OM5, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-SR1.2-100GHT Part Number: QSFP-SR1.2-100G
Product Highlights
- Compatible alternative to Extreme QSFP-SR1.2-100G
- 100G connectivity at 106.25 Gbps
- Optical wavelength: 850/910nm
- Specified reach: 70m on OM3 / 100m on OM4 / 150m on OM5
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -10 to 60 ℃ (14 to 140°F)
Specifications
| HT Part Number | QSFP-SR1.2-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 106.25 Gbps |
| Wavelength | 850/910nm |
| Max. Cable Distance | 70m@OM3/100m@OM4/150m@OM5 |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | Broadcom/AFCD-V7 |
| Receiver Type | PIN |
| TX Power | -6.2dBm~4dBm |
| Minimum Receiver Power | -8.2dBm |
| Power Budget | 2dB |
| Receiver Overload | 4dBm |
| Power Consumption | ≤4W |
| Extinction Ratio | >3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | -10 to 60 ℃ (14 to 140°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 2x 50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | KP4 FEC |
| Packaging Technology | COB Packaging |
| Core Size | 50um/125um |
| Protocols | QSFP28 MSA and IEEE 802.3bm CAUI-4 |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Extreme Compatibility and Factory Testing
Factory verification starts with the expected QSFP-SR1.2-100G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.2dBm~4dBm; the stated optical power budget is 2dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 106.25 Gbps, wavelength 850/910nm, rated reach 70m on OM3 / 100m on OM4 / 150m on OM5.
Ordering Information
Quote HT part number QSFP-SR1.2-100G together with OEM reference QSFP-SR1.2-100G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Extreme transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-SR1.2-100G, not an original Extreme-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 70m on OM3 / 100m on OM4 / 150m on OM5, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
