10/100BASE-T SFPExtreme QSFP-SR4-40G-I Compatible 40G QSFP+ SR4 Transceiver Module
Built for hosts recognizing QSFP-SR4-40G-I, this HT-manufactured QSFP+ module delivers 40G transmission at 850nm. Its rated reach is 150m on OM4 / 100m on OM3, with MTP/MPO-12 Male as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-SR4-40G-IHT Part Number: QSFP-SR4-40G-I
Product Highlights
- Compatible alternative to Extreme QSFP-SR4-40G-I
- 40G connectivity at 41.25Gbps (4x 10.3125Gbps)
- Optical wavelength: 850nm
- Specified reach: 150m on OM4 / 100m on OM3
- MTP/MPO-12 Male / MMF interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-SR4-40G-I |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP+ |
| Max. Data Rate | 41.25Gbps (4x 10.3125Gbps) |
| Wavelength | 850nm |
| Max. Transmission Distance | 150m@OM4/100m@OM3 |
| Connector | MTP/MPO-12 Male |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.6~2.4dBm |
| Receiver Sensitivity | ＜-9.5dBm |
| Power Budget | 1.9dB |
| Receiver Overload | 2.4dBm |
| Max. Power Consumption | ≤1.5W |
| Extinction Ratio | >3dB |
| Host FEC | Supported |
| Bit Error Ratio (BER) | 1E-12 |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
| Protocols | IEEE 802.3ba, QSFP+ MSA, SFF-8436 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 Male interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
The multimode channel should use the fiber grade associated with the stated 150m on OM4 / 100m on OM3 reach. Keep the MTP/MPO-12 Male end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Extreme Compatibility and Factory Testing
Factory verification starts with the expected QSFP-SR4-40G-I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.6~2.4dBm; receiver sensitivity is ＜-9.5dBm; the stated optical power budget is 1.9dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 41.25Gbps (4x 10.3125Gbps), wavelength 850nm, rated reach 150m on OM4 / 100m on OM3.
Ordering Information
Use QSFP-SR4-40G-I as the compatibility cross-reference and QSFP-SR4-40G-I as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Extreme transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-SR4-40G-I, not an original Extreme-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 Male with MMF. The specified maximum reach is 150m on OM4 / 100m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
