10/100BASE-T SFPGeneric QSFP-VR2-200G Compatible 200G QSFP56 VR2 Transceiver Module
The QSFP-VR2-200G compatible module serves equipment requiring a 200G QSFP56 interface with 850nm optics and a 50m rating. Connection is through MPO-12/APC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: QSFP-VR2-200GHT Part Number: QSFP-VR2-200G
Product Highlights
- Compatible alternative to Generic QSFP-VR2-200G
- 200G connectivity at 212.5Gbps(2x 106.25Gbps)
- Optical wavelength: 850nm
- Specified reach: 50m
- MPO-12/APC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 25 to 70°C (77 to 158°F)
Specifications
| HT Part Number | QSFP-VR2-200G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP56 |
| Max. Data Rate | 212.5Gbps(2x 106.25Gbps) |
| Wavelength | 850nm |
| Max. Cable Distance | 50m |
| Connector | MPO-12/APC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -4.6~4dBm |
| Minimum Receiver Power | -6.3dBm |
| Power Budget | 1.7dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 6.5W |
| Extinction Ratio | >2.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 25 to 70°C (77 to 158°F) |
| Modulation (Electrical) | 4x 50G PAM4 |
| Modulation (Optical) | 2x 100G PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | No |
| Protocols | IEEE 802.3db, IEEE 802.3-2022 Annex 120E, QSFP-DD MSA 6.01, CMIS Rev 4.0 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12/APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 200G interface configuration must match the remote equipment; sharing a QSFP56 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 50m figure applies only under suitable cabling conditions. Inspect every MPO-12/APC mating point and match the remote optical standard.
Generic Compatibility and Factory Testing
The module is checked for host recognition as QSFP-VR2-200G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.6~4dBm; the stated optical power budget is 1.7dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 212.5Gbps(2x 106.25Gbps), wavelength 850nm, rated reach 50m.
Ordering Information
Quote HT part number QSFP-VR2-200G together with OEM reference QSFP-VR2-200G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each QSFP-VR2-200G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use MPO-12/APC with MMF. The specified maximum reach is 50m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
