10/100BASE-T SFPJuniper Networks QSFPP-4X10GE-SR Compatible 10G QSFP+ Transceiver Module
The QSFPP-4X10GE-SR compatible module serves equipment requiring a 10G QSFP+ interface with 850nm optics and a 400m on OM4 rating. Connection is through MTP/MPO-12 Male. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: QSFPP-4X10GE-SRHT Part Number: QSFP-CSR4-40G
Product Highlights
- Compatible alternative to Juniper Networks QSFPP-4X10GE-SR
- 10G connectivity at 42Gbps (4x 10.5Gbps)
- Optical wavelength: 850nm
- Specified reach: 400m on OM4
- MTP/MPO-12 Male / MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | QSFPP-4X10GE-SR |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-CSR4-40G |
| Form Factor | QSFP+ |
| Max. Data Rate | 42Gbps (4x 10.5Gbps) |
| Wavelength | 850nm |
| Max. Transmission Distance | 400m@OM4 |
| Connector | MTP/MPO-12 Male |
| Media | MMF |
| Transimitter Type | VCSEL 850nm |
| Receiver Type | PIN |
| TX Power | -7.5~0dBm |
| Receiver Sensitivity | <-9.9dBm |
| Power Budget | 2.4dB |
| Receiver Overload | 2.4dBm |
| Max. Power Consumption | ≤1.5W |
| Extinction Ratio | >3dB |
| Host FEC | Supported |
| Bit Error Ratio (BER) | 1E-12 |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | 40G Ethernet, SATA/SAS3, IEEE 802.3ba, MSA Compliant |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-12 Male interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a QSFP+ housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 400m on OM4 reach. Keep the MTP/MPO-12 Male end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Juniper Networks Compatibility and Factory Testing
The module is checked for host recognition as QSFPP-4X10GE-SR, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.5~0dBm; receiver sensitivity is <-9.9dBm; the stated optical power budget is 2.4dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 42Gbps (4x 10.5Gbps), wavelength 850nm, rated reach 400m on OM4.
Ordering Information
When ordering, specify QSFPP-4X10GE-SR, QSFP-CSR4-40G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFPP-4X10GE-SR, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use MTP/MPO-12 Male with MMF. The specified maximum reach is 400m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
