R0R40AHPE Aruba R0R40A Compatible 100G QSFP28 SR Transceiver Module
The R0R40A compatible module serves equipment requiring a 100G QSFP28 interface with 850/880/910/940nm optics and a 75m on OM3 / 100m on OM4 / 150m on OM5 rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: R0R40AHT Part Number: QSFP-BIDI-100G
Product Highlights
- Compatible alternative to HPE Aruba R0R40A
- 100G connectivity at 103.1Gbps
- Optical wavelength: 850/880/910/940nm
- Specified reach: 75m on OM3 / 100m on OM4 / 150m on OM5
- Duplex LC/UPC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HPE Aruba Compatible | R0R40A |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-BIDI-100G |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.1Gbps |
| Wavelength | 850/880/910/940nm |
| Max. Cable Distance | 75m@OM3/100m@OM4/150m@OM5 |
| Connector | Duplex LC/UPC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -5.5~3dBm |
| Minimum Receiver Power | -9.5dBm |
| Power Budget | 4dB |
| Receiver Overload | 3.4dBm |
| Max. Power Consumption | 3.5W |
| Extinction Ratio | >2dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Packaging Technology | COB Packaging |
| Bit Error Ratio (BER) | 5E-5 |
| MTBF | 11,100,000 Hours (@40°C, 60% CL) |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3bm, CAUI-4 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC/UPC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 75m on OM3 / 100m on OM4 / 150m on OM5 reach. Keep the Duplex LC/UPC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
HPE Aruba Compatibility and Factory Testing
Compatibility testing for R0R40A combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -5.5~3dBm; the stated optical power budget is 4dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 103.1Gbps, wavelength 850/880/910/940nm, rated reach 75m on OM3 / 100m on OM4 / 150m on OM5.
Ordering Information
When ordering, specify R0R40A, QSFP-BIDI-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each R0R40A compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original HPE Aruba transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies R0R40A, not an original HPE Aruba-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with MMF. The specified maximum reach is 75m on OM3 / 100m on OM4 / 150m on OM5, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
