10/100BASE-T SFPExtreme Networks SFP-10G32-BX10-I Compatible 10G SFP+ BX10-D Transceiver Module
Built for hosts recognizing SFP-10G32-BX10-I, this HT-manufactured SFP+ module delivers 10G transmission at 1330nm-TX/1270nm-RX. Its rated reach is 10km, with Simplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10G32-BX10-IHT Part Number: SFP-10G32-BX10-I
Product Highlights
- Compatible alternative to Extreme Networks SFP-10G32-BX10-I
- 10G connectivity at 11.3168Gbps
- Optical wavelength: 1330nm-TX/1270nm-RX
- Specified reach: 10km
- Simplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | SFP-10G32-BX10-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 11.3168Gbps |
| Wavelength | 1330nm-TX/1270nm-RX |
| Max. Transmission Distance | 10km |
| Connector | Simplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -6.5~0.5dBm |
| Receiver Sensitivity | < -14.4dBm |
| Max Power Budget | 7.9dB |
| Receiver Overload | 0.5dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
This single-fiber interface must be paired with the complementary wavelength direction. One end transmits on the wavelength the other receives. Verify connector polish and measure loss over the 10km design range before service.
Extreme Networks Compatibility and Factory Testing
The module is checked for host recognition as SFP-10G32-BX10-I, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~0.5dBm; receiver sensitivity is < -14.4dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 11.3168Gbps, wavelength 1330nm-TX/1270nm-RX, rated reach 10km.
Ordering Information
Quote HT part number SFP-10G32-BX10-I together with OEM reference SFP-10G32-BX10-I and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Extreme Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10G32-BX10-I, not an original Extreme Networks-branded module.
Which fiber and connector are required?
Use Simplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
