10/100BASE-T SFPIntel SFP-10GLRM-31-I Compatible 10G SFP+ LRM Transceiver Module
This Intel SFP-10GLRM-31-I compatible transceiver provides 10G connectivity in a hot-swappable SFP+ package. Its optical design operates at 1310nm for up to 220m on OM3 / 1.4km on SMF, using Duplex LC. Complete parameters and related OEM references help structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: SFP-10GLRM-31-IHT Part Number: SFP-10GLRM-31-I
Product Highlights
- Compatible alternative to Intel SFP-10GLRM-31-I
- 10G connectivity at 10.3125Gbps
- Optical wavelength: 1310nm
- Specified reach: 220m on OM3 / 1.4km on SMF
- Duplex LC / MMF/SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | SFP-10GLRM-31-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 220m@OM3/1.4km@SMF |
| Connector | Duplex LC |
| Media | MMF/SMF |
| Transmitter Type | FP 1310nm |
| Receiver Type | PIN |
| TX Power | -8.2~0.5dBm |
| Receiver Sensitivity | <-14.4dBm |
| Power Budget | 6.2dB |
| Receiver Overload | 0.5dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
| Core Size | 50/125µm@OM3 MMF, 9/125μm@SMF |
| Modulation | NRZ |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 220m on OM3 / 1.4km on SMF figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Intel Compatibility and Factory Testing
Factory verification starts with the expected SFP-10GLRM-31-I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~0.5dBm; receiver sensitivity is <-14.4dBm; the stated optical power budget is 6.2dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 1310nm, rated reach 220m on OM3 / 1.4km on SMF.
Ordering Information
When ordering, specify SFP-10GLRM-31-I, SFP-10GLRM-31-I, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Intel transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10GLRM-31-I, not an original Intel-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF/SMF. The specified maximum reach is 220m on OM3 / 1.4km on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
