10/100BASE-T SFPHPE Aruba SFP-10GM-T-30 Compatible 10G SFP+ Transceiver Module
The SFP-10GM-T-30 compatible module serves equipment requiring a 10G SFP+ interface with the listed wavelength plan optics and a 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable rating. Connection is through RJ-45. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: SFP-10GM-T-30HT Part Number: SFP-10GM-T-30
Product Highlights
- Compatible alternative to HPE Aruba SFP-10GM-T-30
- 10G connectivity at 10.3125Gbps
- Specified reach: 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable
- RJ-45 / Copper interface
- Digital diagnostic monitoring: Not Implemented
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-10GM-T-30 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Max. Power Consumption | ≤2.5W |
| Max. Transmission Distance | 10/100/1000M-100m@Cat 5 Cable or better10G-30m@Cat 6a/7 Cable |
| Connector | RJ-45 |
| Cable Type | Copper |
| Special Features | RX_LOS |
| DDM/DOM | Not Implemented |
| Multi-rate Application | Supported (Auto-negotiation) |
| MTBF | 6430000 Hours |
| EMC (Electro Magnetic Compatibility) | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3az SFP+ MSA |
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this copper interface, use the stated cable category and keep the channel within 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable. Patch-cord construction, connector quality and auto-negotiation can affect the result. Verify the negotiated speed and diagnostics at both ends rather than assuming every RJ-45 port behaves identically.
HPE Aruba Compatibility and Factory Testing
Factory verification starts with the expected SFP-10GM-T-30 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Not Implemented. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10.3125Gbps, rated reach 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable.
Ordering Information
Use SFP-10GM-T-30 as the compatibility cross-reference and SFP-10GM-T-30 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original HPE Aruba transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10GM-T-30, not an original HPE Aruba-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Copper. The rated reach is 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
