10/100BASE-T SFPGeneric SFP-10GMSR-85 Compatible 10G SFP+ SR Transceiver Module
Built for hosts recognizing SFP-10GMSR-85, this HT-manufactured SFP+ module delivers 10G transmission at 850nm. Its rated reach is 300m on OM3 / 400m on OM4, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10GMSR-85HT Part Number: SFP-10GMSR-85
Product Highlights
- Compatible alternative to Generic SFP-10GMSR-85
- 10G connectivity at 1/10.3Gbps
- Optical wavelength: 850nm
- Specified reach: 300m on OM3 / 400m on OM4
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | SFP-10GMSR-85 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 1/10.3Gbps |
| Wavelength | 850nm |
| Max. Transmission Distance | 300m@OM3/400m@OM4 |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.3~-1dBm |
| Receiver Sensitivity | <-11.1dBm |
| Power Budget | 3.8dB |
| Receiver Overload | -1dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3dB |
| DDM/DOM | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Core Size | 50/125µm |
| Modulation | NRZ |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 300m on OM3 / 400m on OM4 figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Generic Compatibility and Factory Testing
Factory verification starts with the expected SFP-10GMSR-85 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.3~-1dBm; receiver sensitivity is <-11.1dBm; the stated optical power budget is 3.8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 1/10.3Gbps, wavelength 850nm, rated reach 300m on OM3 / 400m on OM4.
Ordering Information
Quote HT part number SFP-10GMSR-85 together with OEM reference SFP-10GMSR-85 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 300m on OM3 / 400m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
