SFP-1G-DW17-100Juniper Networks SFP-1G-DW17-100 Compatible 1G SFP Transceiver Module
The SFP-1G-DW17-100 compatible module serves equipment requiring a 1G SFP interface with 1563.86nm optics and a 100km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: SFP-1G-DW17-100HT Part Number: DW-SFP1G100-17
Product Highlights
- Compatible alternative to Juniper Networks SFP-1G-DW17-100
- 1G connectivity at 1000Mbps
- Optical wavelength: 1563.86nm
- Specified reach: 100km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | SFP-1G-DW17-100 |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP1G100-17 |
| Form Factor | SFP |
| Max Data Rate | 1000Mbps |
| Wavelength | 1563.86nm |
| Max Cable Distance | 100km |
| Connector | Duplex LC |
| Optical Components | EML DWDM |
| Media | SMF |
| DOM Support | Yes |
| TX Power | 0~5dBm |
| Receiver Sensitivity | < -32dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | MSA Compliant |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
For this 1563.86nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 100km using the complete channel rather than fiber distance alone.
Juniper Networks Compatibility and Factory Testing
Compatibility testing for SFP-1G-DW17-100 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is < -32dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 1000Mbps, wavelength 1563.86nm, rated reach 100km.
Ordering Information
Quote HT part number DW-SFP1G100-17 together with OEM reference SFP-1G-DW17-100 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-1G-DW17-100, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 100km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
