SFP-GE-T-IHPE ProCurve SFP-GE-T-I Compatible 1G SFP Transceiver Module
Built for hosts recognizing SFP-GE-T-I, this HT-manufactured SFP module delivers 1G transmission at the listed wavelength plan. Its rated reach is 100m, with RJ-45 as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-GE-T-IHT Part Number: SFP-GE-T
Product Highlights
- Compatible alternative to HPE ProCurve SFP-GE-T-I
- 1G connectivity at 1000Mbps
- Specified reach: 100m
- RJ-45 / Cat 6/Cat 6a interface
- Operating temperature: -40 to 85°C (-40 to 185°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-GE-T |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP |
| Max. Data Rate | 1000Mbps |
| Media | Cat 6/Cat 6a |
| Max. Cable Distance | 100m |
| Connector | RJ-45 |
| RX_LOS | NO |
| DOM Support | No |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | MSA Compliant, IEEE STD 802.3 and 802.3ab |
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
The rated 100m copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
HPE ProCurve Compatibility and Factory Testing
Compatibility testing for SFP-GE-T-I combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 1000Mbps, rated reach 100m.
Ordering Information
When ordering, specify SFP-GE-T-I, SFP-GE-T, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original HPE ProCurve transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-GE-T-I, not an original HPE ProCurve-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Cat 6/Cat 6a. The rated reach is 100m, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
