10/100BASE-T SFPCisco SFP28-25GSR-85-I Compatible 25G SFP28 SR Transceiver Module
Built for hosts recognizing SFP28-25GSR-85-I, this HT-manufactured SFP28 module delivers 25G transmission at 850nm. Its rated reach is 100m on OM4 / 70m on OM3, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP28-25GSR-85-IHT Part Number: SFP-25GSR-85-I
Product Highlights
- Compatible alternative to Cisco SFP28-25GSR-85-I
- 25G connectivity at 25.78Gbps
- Optical wavelength: 850nm
- Specified reach: 100m on OM4 / 70m on OM3
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | SFP-25GSR-85-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP28 |
| Max Data Rate | 25.78Gbps |
| Wavelength | 850nm |
| Max Cable Distance | 100m@OM4/70m@OM3 |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -7.9~1.9dBm |
| Receiver Sensitivity | ＜-6dBm |
| Power Budget | -1.9dB |
| Receiver Overload | 2.4dBm |
| Power Consumption | ＜1W |
| Extinction Ratio | ＞2dB |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| CDR | TX & RX Built-in CDR |
| FEC Function | Support RS-FEC, FC-FEC |
| Protocols | IEEE 802.3by, SFF-8472, SFF-8432, SFP28 MSA, CPRI, eCPRI |
| Core Size | 50/125 µm |
| Packaging Technology | COB Packaging |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 100m on OM4 / 70m on OM3 figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Cisco Compatibility and Factory Testing
The module is checked for host recognition as SFP28-25GSR-85-I, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -7.9~1.9dBm; receiver sensitivity is ＜-6dBm; the stated optical power budget is -1.9dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 25.78Gbps, wavelength 850nm, rated reach 100m on OM4 / 70m on OM3.
Ordering Information
When ordering, specify SFP28-25GSR-85-I, SFP-25GSR-85-I, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each SFP28-25GSR-85-I compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP28-25GSR-85-I, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 100m on OM4 / 70m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
