SFP56 to SFP56-50G-DAC-3M10FTSFP56 to SFP56-50G-DAC-3M10FT 50G SFP56 Passive Copper Twinax Cable, 3m (10ft)
This page covers one precise cable-schedule item: Generic SFP56 to SFP56-50G-DAC-3M10FT in 3m (10ft), supporting 50G operation through SFP56 to SFP56. The complete DAC assembly is identified separately from other lengths and includes verified specifications, change-control-friendly ordering details and live-link factory checks.
OEM Part Number: SFP56 to SFP56-50G-DAC-3M10FTHT Part Number: SFP56 to SFP56-50G-DAC-3M10FT
Product Highlights
- HT-manufactured DAC assembly in 3m (10ft)
- 50G connectivity at 50Gbps
- Interface configuration: SFP56 to SFP56
- Fixed length and part number: 3m (10ft), SFP56 to SFP56-50G-DAC-3M10FT
- Cable construction: Passive Twinax
- Conductor specification: 26AWG
- Maximum power consumption: ＜0.1W
Specifications
| HT Part Number | SFP56 to SFP56-50G-DAC-3M10FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP56 to SFP56 |
| Max Data Rate | 50Gbps |
| Cable Length | 3m(10ft) |
| Wire AWG | 26AWG |
| Power Consumption | ＜0.1W |
| Jacket Material | PVC |
| Cable Type | Passive Twinax |
| Compatible | Generic |
| Temperature | 0°C to 70°C (32 to 158°F) |
| Application | 50G Ethernet |
| Modulation Technology | PAM4 |
| Protocol | SFP28 MSA SFF-8432 |
Power and Thermal Planning
The rated power consumption is ＜0.1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Passive Copper Operation
A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.
Length Selection and Installation Planning
At 3m (10ft), this assembly can bridge non-aligned ports or adjacent racks while remaining a single direct-attach link. Support longer horizontal runs with suitable cable management and preserve space for cooling and future maintenance.
Position Within the Length Range
SFP56 to SFP56-50G-DAC-3M10FT is the longest of 3 verified length options in this family. Compared with SFP56 to SFP56-50G-DAC-2M7FT at 2m (7ft), it provides 1m of additional reach for a longer vertical drop, a wider rack or an adjacent-cabinet route. Confirm that the complete path requires this length, because unused slack still needs supported, bend-safe storage.
Structured Pathways and Serviceability
Treat the direct-attach assembly as part of the permanent pathway plan even when the link is expected to be temporary. Follow the intended horizontal and vertical managers, maintain the specified bend radius and leave service access around both ports. A small, supported service allowance is preferable to excess slack concealed inside a rack or placed under cable-tie pressure. For this assembly, the listed conductor specification is 26AWG; the stated power consumption is ＜0.1W; the jacket material is PVC.
Cable Construction and Routing
This assembly uses 26AWG conductors, PVC jacket. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is 50G Ethernet.
Ordering Information
Include the part number, fixed length, quantity and required pathway or rack grouping in the order information. The host model and firmware release are useful for change-controlled deployments. Different lengths should remain separate order lines so delivered labels and packing records agree with the pathway plan. Keep SFP56 to SFP56-50G-DAC-3M10FT associated with 3m (10ft) throughout the order and receiving record.
Generic Compatibility and Factory Testing
Verification covers the physical connectors, expected host identity and an operating link with available diagnostic indications. We distinguish this complete check from a simple continuity test. Platform model and software release can be reviewed in advance where the installation has strict documentation or change-control requirements. Where supported by the host, link stability and diagnostic indications are reviewed together with the established link.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
Quality Assurance and Packaging
After connector inspection and link verification, the assembly is coiled without tight bends and packed with end protection. Labels can cross-reference the customer cable schedule, OEM part number and length. This supports both receiving checks and later moves, adds or changes. Volume orders can include customer references on the labels and carton list.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
