10/100BASE-T SFPJuniper Networks SFPP-10G-DT-ZRC2 Compatible 10G SFP+ Transceiver Module
Built for hosts recognizing SFPP-10G-DT-ZRC2, this HT-manufactured SFP+ module delivers 10G transmission at 1529.16~1567.13nm (Tunable）. Its rated reach is 80km, with Duplex LC as the physical interface. The specifications and engineering guidance below support structured fiber installations preserve a documented and serviceable optical channel, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFPP-10G-DT-ZRC2HT Part Number: DW-SFP10G80-C
Product Highlights
- Compatible alternative to Juniper Networks SFPP-10G-DT-ZRC2
- 10G connectivity at 10.3125Gbps
- Optical wavelength: 1529.16~1567.13nm (Tunable）
- Specified reach: 80km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Compatible | SFPP-10G-DT-ZRC2 |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP10G80-C |
| Form Factor | SFP+ |
| Max Data Rate | 10.3125Gbps |
| Connector | Duplex LC |
| Max Cable Distance | 80km |
| Media | SMF |
| Wavelength | 1529.16~1567.13nm (Tunable） |
| Modulation | NRZ |
| Power Consumption | < 2W |
| Transmitter Type | Monolithic MZM Tunable TOSA |
| Receiver Type | APD |
| Power Budget | 22dB（@9.95Gbps~10.7Gbps)25dB（@11.3Gbps） |
| Extinction Ratio | 8.2dB |
| CDR | Yes |
| BER | 1E-12 |
| TX Power | -1~3dBm |
| Receiver Overload | -1dBm |
| EMC (Electro Magnetic Compatibility) | Supported |
| DDM/DOM Support | Yes |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Inbuilt FEC | NO |
| Protocols | IEEE 802.3ae CL 52 MSA SFF-8472 MSA SFF-8431 MSA SFF-8690ITU-T G.698.1 |
| Application | Ethernet, SONET/SDH |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this coherent interface, document the wavelength plan and modulation or FEC settings before commissioning. Measure span loss and verify adequate OSNR. Interoperability depends on compatible coherent modes as well as form factor, so another coherent part number must not be substituted without engineering review.
Juniper Networks Compatibility and Factory Testing
Factory verification starts with the expected SFPP-10G-DT-ZRC2 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~3dBm; the stated optical power budget is 22dB（@9.95Gbps~10.7Gbps)25dB（@11.3Gbps）. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 1529.16~1567.13nm (Tunable）, rated reach 80km.
Ordering Information
When ordering, specify SFPP-10G-DT-ZRC2, DW-SFP10G80-C, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFPP-10G-DT-ZRC2, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 80km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
