10G-SFPP-LRM2Brocade 10G-SFPP-LRM2 Compatible 10G SFP+ LRL Transceiver Module
This Brocade 10G-SFPP-LRM2 compatible transceiver provides 10G connectivity in a hot-swappable SFP+ package. Its optical design operates at 1310nm for up to 2km, using Duplex LC. Complete parameters and related OEM references help structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: 10G-SFPP-LRM2HT Part Number: SFP-10GLRL-31
Product Highlights
- Compatible alternative to Brocade 10G-SFPP-LRM2
- 10G connectivity at 10Gbps
- Optical wavelength: 1310nm
- Specified reach: 2km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Brocade Compatible | 10G-SFPP-LRM2 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLRL-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 2km |
| Connector | Duplex LC |
| Transmitter Type | FP 1310nm |
| Media | SMF |
| DOM Support | YES |
| TX Power | -8.2~0.5dBm |
| Receiver Sensitivity | <-12.6dBm |
| Max. Power Consumption | ≤1.2W |
| Receiver Overload | +1.5dBm |
| Core Size | 9/125μm@SMF |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 2km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Brocade Compatibility and Factory Testing
Compatibility testing for 10G-SFPP-LRM2 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~0.5dBm; receiver sensitivity is <-12.6dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10Gbps, wavelength 1310nm, rated reach 2km.
Ordering Information
Use 10G-SFPP-LRM2 as the compatibility cross-reference and SFP-10GLRL-31 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each 10G-SFPP-LRM2 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 10G-SFPP-LRM2, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
