10/100BASE-T SFPNETGEAR AXM764 Compatible 10G SFP+ LRL Transceiver Module
The AXM764 compatible module serves equipment requiring a 10G SFP+ interface with 1310nm optics and a 2km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support structured fiber installations preserve a documented and serviceable optical channel.
OEM Part Number: AXM764HT Part Number: SFP-10GLRL-31
Product Highlights
- Compatible alternative to NETGEAR AXM764
- 10G connectivity at 10Gbps
- Optical wavelength: 1310nm
- Specified reach: 2km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| NETGEAR Compatible | AXM764 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLRL-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 2km |
| Connector | Duplex LC |
| Transmitter Type | FP 1310nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | -8.2~0.5dBm |
| Receiver Sensitivity | <-12.6dBm |
| Max. Power Consumption | ≤1.2W |
| Receiver Overload | +1.5dBm |
| Core Size | 9/125μm@SMF |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 2km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
NETGEAR Compatibility and Factory Testing
Compatibility testing for AXM764 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~0.5dBm; receiver sensitivity is <-12.6dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Structured Fiber Pathways and Serviceability
Treat the transceiver as part of the complete channel. Follow the intended patch-panel route, maintain bend control and leave service access around the port. Confirm connector polish and fiber type at every mated pair; a documented service allowance is preferable to excess slack concealed inside a rack. For this model, the principal parameters are data rate 10Gbps, wavelength 1310nm, rated reach 2km.
Ordering Information
When ordering, specify AXM764, SFP-10GLRL-31, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original NETGEAR transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies AXM764, not an original NETGEAR-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
